JLG 400S Скачать руководство пользователя страница 68

Страница: 68 / 145

SECTION 4 - MACHINE OPERATION

4-6

31215015

Pull out the Ground Console Power/Emer

gency Stop switch to provide power to the
platform controls.

From Platform Control Console, pull Power/
Emergency Stop switch out.

Push the Engine Start switch until engine starts.

NOTE:

Footswitch must be in released (up) position before starter will
operate. If starter operates with footswitch in the depressed posi

tion, DO NOT OPERATE MACHINE.

Shutdown Procedure

IF AN ENGINE MALFUNCTION CAUSES AN UNSCHEDULED SHUTDOWN, DETERMINE
THE CAUSE AND CORRECT IT BEFORE RESTARTING THE ENGINE.

Remove all load and allow engine to operate at low speed
for 3-5 minutes; this allows further reduction of internal
engine temperature.

Push Power/Emergency Stop switch in.

Turn Platform/Ground Select switch to Off.

Refer to Engine Manufacturer’s manual for detailed
information.

order go

Discount-Equipment.com

Содержание 400S


















































































































































Результаты поиска

Содержание 400S

Отзывы:

JLG 400S, Руководство по эксплуатации и безопасности, Страница: 68 / 145

Результаты поиска

Содержание 400S

Отзывы: