JLG 1930ES, Инструкция по эксплуатации и безопасности

Страница: 24 / 50

SECTION 3 - USER RESPONSIBILITIES AND MACHINE CONTROL
3-4 – JLG Lift – 3121165
3.5 PLATFORM CONTROL STATION
NOTE: The platform control indicator panel uses different
shaped symbols to alert the operator to different
types of operational situations that could arise. The
meaning of those symbols are explained below.
CONTROL BOXES SHOULD NOT BE SWITCHED FROM ONE
MACHINE TO ANOTHER.
1. Indoor (CE) / Zone A Capacity (ANSI/AUS) - This
indicator light will be illuminated when the Indoor
(CE) or Zone A (ANSI/AUS) capacity is selected.
2. Outdoor (CE) / Zone B Capacity (ANSI/AUS) - This
indicator light will be illuminated when the Outdoor
(CE) or Zone B (ANSI/AUS) capacity is selected.
3. System Distress Indicator - This indicator will light up
with a fault flash code that will determine where a
problem, within the system, exists.
4. Battery Discharge Indicator (BDI) - This set of lights
is designed to let the operator know the condition of
the batteries.
5. Tilt Indicator Warning Light - A red warning light on
the control panel that illuminates when the chassis is
on a slope greater than what the machine is pro-
grammed for.
6. Overload Indicator (If Equipped) - Indicates the plat-
form has been overloaded.
NOTE: If the Overload Indicator is illuminated, fully lower the
machine and reduce the weight in the platform so as
to not exceed the rated workload indicated on the
capacity decal.
7. Capacity Select Switch - On model 2630ES/3246ES
machines this switch is used to choose allowable
capacity zone. On all CE machines, except the
2630ES, this switch is used to select either indoor or
outdoor capacity zone.
8. Lift/Drive Select - This toggle switch is used to select
either drive or lift. After selecting a function, the con-
troller must be moved in the proper direction in
order to activate that function. The function must be
selected with the joystick in the neutral position. Oth-
erwise, the function select will not occur.
9. Horn - This push-button switch, when activated, per-
mits the operator to warn jobsite personnel when the
machine is operating in the area.
10. Steer Switch - The steer switch is a thumb operated
switch located at the top of the control handle.
Depressing the switch to the right will steer the
wheels to the right. Depressing the switch to the left
will steer the wheels to the left.
11. Controller - The control handle controls three func-
tions: drive, lift, and steer. The drive and lift switch
must be selected prior to moving the control handle.
After selecting the drive function, moving the control
handle forward will drive the machine forward and
moving the control handle backwards will drive the
machine backward. After selecting the lift function,
moving the control handle backward will lift the
machine up and moving the control handle forward
will lift the machine down. The speed on all selected
functions is proportionally controlled by the distance
of travel of the hand controller. The thumb-operated
steer switch on top of the hand controller activates
the steer wheels in the direction activated (right or
left).
12. Emergency Stop Switch - A two-position, red, mush-
room-shaped emergency stop switch functions to
provide power to the platform control station and
also to turn off power to the platform function con-
trols in the event of an emergency. With the Power
selector switch positioned to platform, power is
turned on by pulling the switch out (on), and is
turned off by pushing the switch in (off).
Indicates a potentially hazardous situation,
which if not corrected, could result in serious
injury or death. This indicator will be red.
Indicates an abnormal operating condition,
which if not corrected, may result in machine
interruption or damage. This indicator will be
yellow.
Indicates important information regarding the
operating condition, i.e. procedures essential
for safe operation. This indicator will be
green with the exception of the capacity indi-
cator which will be green or yellow depend-
ing upon platform position.