JLG 1850SJ, Руководство по обслуживанию и ремонту, Страница: 116 / 712

SECTION 3 - CHASSIS & TURNTABLE
3-66 3121619
73 7-2-2 523912 4 @ engines < 4l:
Throttle valve error, Open Load or Short cut
to Battery, blocked valve or wrong control
signal for valve.
@ engines with Burner T4i:
Pressure Sensor error after valve (DV2),
lower limit reached The sensed raw voltage value is below the mini-
mum threshold. The sensed raw voltage value
DPM_uRawBrnDVDsP is above the minimum
threshold
DPM_SRCBrnDVDsP.uMin_C
@ CRT < 4l: check throttle valve
@ engines with Burner T4i: check back-pressure
valve
84 271 639 14 CAN bus 0: the ECU is not allowed to send
messages, because the status "BusOff" is
detected. CAN BusOff error; CAN 0 (Customer CAN) Threshold for error detection is an internal ECU
threshold.
BusOff bit for CAN A node is set.
Check wiring of CAN bus and if necessary repair
it, check connection cable and if
necessary repair or replace it, check resistance in
CAN lines (120 Ohm)
85 271 1231 14 CAN bus 1: the ECU is not allowed to send
messages, because the status "BusOff" is
detected
Warning, no diagnostic with SERDIA2010
possible CAN BusOff error; CAN 1 (Diagnostic CAN) Threshold for error detection is an internal ECU
threshold.
BusOff bit for CAN B node is set.
Check wiring of CAN bus and if necessary repair
it, check connection cable and if
necessary repair or replace it, check resistance in
CAN lines (120 Ohm)
86 271 1235 14 CAN bus 2: the ECU is not allowed to send
messages, because the status "BusOff" is
detected.
Warning, depends on engine, EAT. CAN BusOff error; CAN 2 (Engine CAN) Threshold for error detection is an internal ECU
threshold.
BusOff bit for CAN C node is set.
Check wiring of CAN bus and if necessary repair
it, check connection cable and if
necessary repair or replace it, check resistance in
CAN lines (120 Ohm)
88 223 102 2 Charge air pressure messured by sensor is
above the shut off threshold. Charged air cooler pressure below threshold. Check waste gate system if necessary replace
TC,
check CAC if all channels are clean,check charge
air piping if nececery.
89 223 102 2 Charge air pressure messured by sensor is
above the warning threshold Charge air pressure above shut off threshold Check waste gate system if necessary replace
TC, check CAC if all channels are clean,
check charge air piping if necessery.
93 225 110 1 Coolant temperature sensor: the voltage of
the sensor measured by ECU is out of the tar-
get range. Suspected components:wiring harness, cool-
ant temperature sensor. Check wiring harness and connected Coolant
Temp Sens.
96 225 110 3 Coolant temperature sensor: the voltage of
the sensor measured by ECU is out of the tar-
get range Short cut to battery or open load. Check sensor and if necessary replace it, check
connection cable and if necessary
repair or replace it.
97 225 110 4 Coolant temperature sensor: the voltage of
the sensor measured by ECU is out of the tar-
get range Voltage Surveillance has found shortcut to
Ground at Coolant Temperatur Sensor. Check sensor and if necessary replace it, check
connection cable and if necessary
repair or replace it
Measure Voltage at Coolant Temperature Sen-
sor and renew harness if needed.
98 232 110 0 Coolant temperature: the coolant tempera-
ture calculated by ECU is above the target
range; the ECU activates a system reaction Cooling temperature too high. Coolant temper-
ature above warning threshold Clean radiator, check fan drive, check coolant
level, check cooling system in general,
check thermostat function, check water pump
Table 3-10. Engine Fault Codes
Deutz
Code
Blink
Code
SPN FMI Description Possible Cause Action