JLA D30 Phase 7 Non-Coin страница 29 Скачать руководство пользователя

Страница: 29 / 60

2. Technical Gas Data

a. Gas Specifications

Shaded areas are stated in metric equivalents

* Measured at gas valve pressure tap when the gas valve is on.

b. Gas Connections

Inlet connection ----------- 1/2” N.P.T.
Inlet supply size ----------- 1/2” N.P.T. (minimum)
Heat input (per dryer) --- 78,000 Btu/hr (19,656 kcal/hr)

1) Natural Gas

Regulation is controlled by the dryer’s gas valve’s internal regulator. Incoming supply pressure

must be

consistent between a minimum of 6.0 inches (19.92 mb) and a maximum of 12.0 inches

(29.9 mb) water column (W.C.) pressure.

2) Liquid Propane (L.P.) Gas

Dryers made for use with L.P. gas have the gas valve’s internal pressure regulator blocked open so
that the gas pressure

must be

regulated upstream of the dryer. The pressure measured at each

gas valve pressure tap

must be

a consistent 10.5 inches (26.2 mb) water column. There is no

regulator or regulation provided in an L.P. dryer. The pressure

must be

regulated at the source

(L.P. tank) or an external regulator

must be

added to each dryer.

Shaded area is stated in metric equivalent

* Drill Measurement Size (D.M.S.) equivalents are as follows:

Natural Gas .............................. #31 = 0.1200” (3.048 mm).
Liquid Propane Gas .................. #51 = 0.0670” (1.701 mm).

TYPE OF GAS

NATURAL

LIQUID PROPANE

Manifold Pressure*

3.5 inches W.C.

8.7 mb

10.5 inches W.C.

26.1 mb

In-Line Pressure

6.0 - 12.0 inches W.C.

14.92 - 29.9 mb

11.0 inches W.C.

27.4 mb

TYPE OF GAS

Liquid

Propane

Conversion Kit

Part Number

Btu/hr

Rating

kcal/hr

Rating

Natural

Liquid Propane

Qty.

D.M.S.*

Part No.

Qty.

D.M.S.*

Part No.

78,000

19,656

#31

140818

#51

140801

883297

Содержание D30 Phase 7 Non-Coin





























































Результаты поиска

Содержание D30 Phase 7 Non-Coin

Отзывы:

Похожие инструкции для D30 Phase 7 Non-Coin

Бренды по названию

Популярные бренды

JLA D30 Phase 7 Non-Coin, Руководство по установке

Результаты поиска

Содержание D30 Phase 7 Non-Coin

Отзывы:

Похожие инструкции для D30 Phase 7 Non-Coin

Бренды по названию

Популярные бренды