JLA D30 Phase 7 Non-Coin страница 28 Скачать руководство пользователя | Manualshive

Страница: 28 / 60

background image

24

G. GAS INFORMATION

It is your responsibility to have

ALL

plumbing connections made by a qualified professional to assure that the gas

plumbing installation is adequate and conforms to local and state regulations or codes. In the absence of such
codes,

ALL

plumbing connections, materials, and workmanship

must conform

to the applicable requirements of

the National Fuel Gas Code ANSI Z223.1-LATEST EDITION, or in Canada, the Canadian Installation Codes
CAN/CGA-B149.1-M91 (Natural Gas) or CAN/CGA-B149.2-M91 (Liquid Propane [L.P.] Gas) or LATEST
EDITION.

IMPORTANT:

Failure to comply with codes or ordinances, and/or requirements in this manual, can
result in personal injury and improper operation of the dryer.

The dryer and its individual shutoff valves

must be

disconnected from the gas supply piping system during any

pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa). The dryer

must be

isolated

from the gas supply piping system by closing its individual manual shutoff valve during any pressure test of the
gas supply piping system at test pressures equal to or less than 1/2 psig (3.5 kPa).

IMPORTANT:

Failure to isolate or disconnect the dryer from supply as noted can cause irreparable
damage to the gas valve, which will

VOID THE WARRANTY.

WARNING: FIRE OR EXPLOSION COULD RESULT

.

1. Gas Supply

The gas dryer installation

must meet

the American National Standard...National Fuel Gas Code ANSI

Z223.1-LATEST EDITION, or in Canada, the Canadian Installation Codes CAN/CGA-B149.1 M91 (Natural
Gas) or CAN/CGA-B149.2-M91 (L.P. Gas) or LATEST EDITION, as well as local codes and ordinances
and

must be

done by a qualified professional.

NOTE:

Undersized gas piping will result in ignition problems, slow drying, increased use of energy, and
can create a safety hazard.

The dryer

must be

connected to the type of heat/gas indicated on the dryer data label, which is located on

the left side panel area behind the top control (access) door. If this information does not agree with the type
of gas available,

DO NOT operate the dryer

. Contact the distributor who sold the dryer or contact

JLA

.

IMPORTANT:

Any burner changes or conversions

must be

made by a qualified professional.

The input ratings shown on the dryer data label are for elevations up to 2,000 feet (610 meters), unless
elevation requirements of over 2,000 feet (610 meters) were specified at the time the dryer order was
placed with the factory. The adjustment or conversion of dryers in the field for elevations over 2,000 feet
(610 meters) is made by changing each burner orifice. If this conversion is necessary, contact the distributor
who sold the dryer or contact

JLA

.

IMPORTANT:

THIS GAS DRYER

IS

NOT

PROVIDED WITH AN INTERNAL GAS SUPPLY

SHUTOFF AND AN EXTERNAL GAS SUPPLY SHUTOFF

MUST BE

PROVIDED.

«
...
26
27
28
29
30
...
»

Содержание D30 Phase 7 Non-Coin





























































Отзывы:

Нет отзывов

Похожие инструкции для D30 Phase 7 Non-Coin

Бренд: Canmac Страницы: 17

Бренд: Gorenje Страницы: 48

Бренд: Smeg Страницы: 27

Бренд: Alliance Laundry Systems Страницы: 19

01.182026.01.001

Бренд: Princess Страницы: 66

TKG FTL 1090 BU

Бренд: Team Kalorik Страницы: 60

Бренд: PITSOS Страницы: 12

AEQ6700FS - 27" Electric Dryer

Бренд: Frigidaire Страницы: 15

Бренд: Frigidaire Страницы: 11

Бренд: Frigidaire Страницы: 10

Бренд: Frigidaire Страницы: 8

Affinity FAQE7072L

Бренд: Frigidaire Страницы: 3

Бренд: Frigidaire Страницы: 10

Affinity FAQE7011L

Бренд: Frigidaire Страницы: 3

Бренд: Frigidaire Страницы: 22

Affinity FAQE7001L

Бренд: Frigidaire Страницы: 3

Affinity FAQE7001LW

Бренд: Frigidaire Страницы: 2

Бренд: Frigidaire Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды