JetPaks 2003 Bullfrog Portable Скачать руководство пользователя

Страница: 29 / 40

Page 29

Bullfrog Spas Owner’s Manual

face plate of the filter assembly. The depth range of

these marks is 6-7½” down from top of spa.

Note 1:

To avoid air pockets in the pumps and in the

main plumbing intake, it is recommended that the spa be

refilled through the filter assembly.

Note 2:

The higher the water level, the fewer spa users

it will take to cause the water to overflow the top of the

spa.

Note 3:

Do not fill your spa with soft water unless the

mineral content is raised immediately.

4. Restore electrical power supply.

5. See "Starting Your Spa with New Water" under "Water

Chemistry" in this Owner's Manual.

CLEANING YOUR FILTER

Cleaning the Filter Cartridge:

It is recommended that your Filter Cartridge(s) be

cleaned every 3 to 6 weeks or as needed. Replace the

Filter Cartridge(s) approximately every two years or when

necessary. To maintain warranty protection, use only

Bullfrog Filter Cartridge replacements.

1. Put the spa in "Standby Mode". This will prevent the

pump from activating while cleaning the cartridge. (See

“Standby Mode” under "OPERATION" in this Owner's

Manual.)

2. Remove skimmer face-plate and basket.

3. Grasp cartridge(s) and lift out. With a garden hose and

nozzle or other high pressure device, hose cartridge(s)

clean with jet stream of water. Work top to bottom on

each pleat. To remove collected suntan lotions and body

oils that hosing will not remove; soak cartridge(s) in

warm water with a FILTER CLEANER or detergent added.

To remove calcium deposits (a white chalky material)

soak cartridge(s) in a one part muriatic acid to ten parts

water solution. USE A PLASTIC CONTAINER ONLY.

Calcium deposits indicate a high spa pH, which should

be corrected.

5. CAUTION: Using a brush to clean a cartridge could

damage it. Bullfrog’s SpinClean™ filter cartridge cleaners

may be used and can be obtained from your authorized

Bullfrog Portable Spa Dealer.

6. Reinstall cartridge(s), basket and skimmer face-plate.

7. Press any button on the control pad to reset the

control system.

LIGHT BULB REPLACEMENT

To replace a burned out or defective light bulb, complete

the following steps:
1. Disconnect electrical power supply.
2. Remove the door to the Equipment Compartment.

(Figure T) Filter Location

Содержание 2003 Bullfrog Portable









































Результаты поиска

Содержание 2003 Bullfrog Portable

Отзывы:

Похожие инструкции для 2003 Bullfrog Portable

Бренды по названию

Популярные бренды

JetPaks 2003 Bullfrog Portable, Руководство пользователя

Результаты поиска

Содержание 2003 Bullfrog Portable

Отзывы:

Похожие инструкции для 2003 Bullfrog Portable

Бренды по названию

Популярные бренды