JetPaks 2003 Bullfrog Portable Скачать руководство пользователя

Страница: 20 / 40

Page 20

Bullfrog Spas Owner’s Manual

If the problem persists, contact your dealer or service

organization.

Check water level in spa. Refill if necessary. If the

water level is okay, make sure the pumps have been

primed. If problem persists, contact your dealer or

service organization.

Follow action required for “HFL” message. Heating ca-

pacity of the spa will not reset automatically; you may

press any button to reset.

Check water level in spa. Refill if necessary. If the wa-

ter level is okay, make sure the pumps have been

primed. Press any button to reset.

Follow action required for “dr” message. Spa will not

automatically reset; you may press any button to re-

set.

See the M-7 Installation Instruction Manual for com-

plete instructions on Power-up and Pump Priming. The

Priming mode will last for up to 4 minutes and then

the spa will begin to heat and maintain the water tem-

perature in the Standard mode.

After the pump has been running for 2 minutes, the

temperature will be displayed.

In Economy or Sleep mode, the pump may be off for

hours outside a filter. If you wish to see the current

spa temperature, either switch to Standard mode or

turn Jets1 on for at least two minutes.

Repair required. Contact your dealer or service organi-

zation.

Press any button to leave Standby Mode and return to

normal operation.

Add pH increaser according to manufacturer’s

instructions.

Add pH decreaser according to manufacturer’s

instructions.

Add sanitizer according to manufacturer’s

instructions.

Remove spa cover and allow sanitizer to dissipate.

Sensors are out of balance. If this is

alternating with the temperature, it may

just be a temporary condition. If the dis-

play shows only this message (periodically

blinking), the spa is shut down.

A substantial difference between the tem-

perature sensors was detected. This could

indicate a flow problem.

Persistent low flow problems. (Displays on

the fifth

occurrence of the “HFL” message within 24

hours.)

Inadequate water detected in heater.

(Displays on third occurrence of “dr” mes-

sage.) Spa is shut down.

When your spa is first actuated, it will go

into Priming mode.

Temperature unknown.

Temperature not current in Economy or

Sleep mode.

Internal problem detected.

Standby Mode has been activated by

pressing a button combination on the user

panel.

pH is low.

pH is high.

Sanitizer is low.

Sanitizer is high.

Содержание 2003 Bullfrog Portable









































Результаты поиска

Содержание 2003 Bullfrog Portable

Отзывы:

Похожие инструкции для 2003 Bullfrog Portable

Бренды по названию

Популярные бренды

JetPaks 2003 Bullfrog Portable, Руководство пользователя

Результаты поиска

Содержание 2003 Bullfrog Portable

Отзывы:

Похожие инструкции для 2003 Bullfrog Portable

Бренды по названию

Популярные бренды