background image

6.TMWG. 3

THE JETMASTER UNITISTOBE INSTALLED BY A CERTIFIED FIREPLACE INSTALLER , APPROVED NZHHA 

INSTALLATION TECHNICIAN OR A CERTIFIED GAS FITTER

Head Office & Showroom

12 Tawari St, Mt Eden, Auckland 

Ph: 09 623 699

0

thefireplace.co.nz

AS/NZS2918:2001 GENERAL NOTES – SOLID FUEL

THE APPLIANCE AND FLUE SYSTEM SHALL BE INSTALLED IN ACCORDANCE WITH AS/NZS2918 AND THE 

APPROPRIATE REQUIREMENTS OF THE RELEVANT BUILDING CODE OR CODES.

FLUE SYSTEM MAY 

REQUIRE TO BE DOUBLE LINED TO COMPLY. REF. ASNZS2918:2001 4.3 FLUE PIPE CASING

MIXING OF APPLIANCE OR FLUE SYSTEM COMPONENTS FROM DIFFERENT SOURCES OR MODIFYING THE

DIMENSIONAL SPECIFICATION OF COMPONENTS MAY RESULT IN HAZARDOUS CONDITIONS. WHERE SUCH

ACTION IS CONSIDERED, THE MANUFACTURER SHOULD BE CONSULTED IN THE FIRST INSTANCE.

CRACKED AND BROKEN COMPONENTS, e.g. GLASS PANELS OR CERAMIC TILES, MAY RENDER THE

INSTALLATION UNSAFE.

DO NOT USE FLAMMABLE LIQUIDS OR AEROSOLS TO START OR REKINDLE THE FIRE OR IN THE VICINITY 

OF THIS APPLIANCE WHEN OPERATING.

DO NOT STORE FUEL WITHIN HEATER INSTALLATION CLEARANCES.

WHEN OPERATING THIS APPLIANCE AS AN OPEN FIRE USE A FIRE SCREEN.

THIS APPLIANCE SHOULD BE MAINTAINED AND OPERATED AT ALL TIMES IN ACCORDANCE WITH THESE

INSTRUCTIONS.

USE OF SOME TYPES OF PRESERVATIVE-TREATED WOOD AS A FUEL CAN BE HAZARDOUS.

IF INSTALLED IN A COMMERCIAL SETTING A SACRIFICIAL PLATE MUST BE FITTED TO THE BACK OF THE 

FIRE TO COMPLY WITH JM FIREBOX WARRANTY CONDITIONS.

THE FLUE SYSTEM SHOULD BE CLEANED EVERY 12 MONTHS.

AS/NZS5601:2013 GENERAL NOTES – GAS

THE APPLIANCE AND FLUE SYSTEM SHALL BE INSTALLED IN ACCORDANCE WITH AS/NZS5601:2013 ,

AS/NZS 5263:2017 and THE APPROPRIATE REQUIREMENTS OF THE RELEVANT BUILDING CODE OR CODES.

DO NOT USE FLAMMABLE LIQUIDS OR AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHEN ITS 

OPERATING.

THIS IS PRIMARILY A DECORATIVE APPLIANCE. IT IS NOT CERTIFIED AS A SPACE HEATER.

EACH UNIT IS DESIGNED FOR USE ONLY WITH THE TYPE OF GAS FOR WHICH IT IS INTENDED.

LPG OR NG

THEGASBURNERSHOULDBESERVICEDEVERY12MONTHS

WARNING: IF A GAS SMELL IS DETECTED, IRRESPECTIVE OF WHETHER THE UNIT IS IN OPERATION OR 

SWITCHED OFF, ACTION MUST BE TAKEN IMMEDIATELY! SWITCH THE UNIT OFF!

SHUT DOWN THE GAS SUPPLY TO THE UNIT AT THE VALVE! CONTACT A GAS FITTER!

IMPORTANT

Содержание 700


















Отзывы: