background image

                             

                                                                                      WE ARE HERE TO SURPRISE! 

 

         

 

1.4 Notice of environment and condition. 
 

In general, this auto lift to be installed on the following terms:

 

1.4.1 Supply voltage: 0.9-1.1 nominal supply voltage. 

1.4.2 Source frequency: 0.99 to 1.01 nominal frequency. 

1.4.3 Ambient temperature: 5 ° C - 40 ° C 

1.4.4 Height: must be at altitudes of up to 1000 m above sea level. 

1.4.5 Humidity: Not to exceed 50% at 40 ° C 

1.4.6 Atmosphere: Free from dust, acid fumes, corrosive gases and salt. 

1.4.7 Avoid exposure to direct sunlight or heat rays that can alter the environmental temp. 

1.4.8 Avoid exposure to abnormal vibrations. 

1.4.9 Electrical equipment must withstand the effects of transport and storage temperature within a range 

of -10 ° C to 55 ° C and for short periods of max. +60 ° C - no more than 24 hours. 

 
1.5 Warning signs. 

All safety warning signs attached on the machine are for the purpose of 

drawing the user’s attention to safety operation. The 

labels must be kept clean and need to be replaced when they are worn-out or fallen off. Read the explanations of the labels 

carefully and try to memorize them.   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Содержание Euroline JA3000S-E





















Отзывы: