JCM ivizion ld Скачать руководство пользователя

Страница: 35 / 158

P/N 960-100929R_Rev. 7 {EDP #148849}

2 - 1

iVIZION® Series

Next-Generation Banknote Acceptor Unit

S e c t i o n 2

This section provides installation and operating
instructions for the iVIZION

Series Next-Genera-

tion Banknote Acceptor Unit. The information

within this section contains the following features:

•

Installation Procedure

•

DIP Switch Configurations

•

Connector Pin Assignments

•

Preventive Maintenance

•

Cleaning Procedure

•

Standard Interface Circuit Schematics

•

Operation Flowcharts

Installation Procedure

Mounting holes are provided in each Frame Unit to

attach the iVIZION to a related Machine during

installation. Select and perform the following steps

to install the iVIZION Unit in the related

Machine’s particular Frame configuration:

1. Install the Interface Harness to the Frame

Grounding Plate (FG PLT) (Figure 2-1

) using

the two (2) Floating Collars (Figure 2-1

), the

single (1) M2.6x12 W Washer Screw (Figure 2-1

), the single (1) M2.6x10 W Washer Screw (Fig-

ure 2-1

) and the single (1) M2.6 Nylon Nut

(Figure 2-1

) onto the Frame Assembly. See the

Figure 2-1 circled inset to visually see the assem-

bly completed as required.

2. When a side mounting configuration is preferred,

bolt the left and right side of the

iVIZION

Frame into its intended

related Machine’s

loca-

tion using six (6) M4 Screws on both sides of the

Frame (3 Screws on each side as shown in Figure

2-2).

3. When an end mounting configuration is pre-

ferred, remove the Cash Box and attach the rear

end of the

iVIZION

Frame into its intended

location using four (4) UNC6-32 Flat Head

Screws from inside the back end of the Frame as

shown in Figure 2-3.

2 INSTALLATION

Figure 2-1

Interface Harness Installation Loca-

tion

Figure 2-1

Interface Harness Installation Location

Figure 2-2

M4 Screws Locations (Left/Right

Side)

Figure 2-2

M4 Screws Locations (Left/Right Side)

Figure 2-3

Flat Head Screws Locations (Rear

Side)

Figure 2-3

Flat Head Screws Locations
(Rear Side)

Содержание ivizion ld































































































































































Результаты поиска

Содержание ivizion ld

Отзывы:

Похожие инструкции для ivizion ld

Бренды по названию

Популярные бренды

JCM ivizion ld, Эксплуатация и обслуживание

Результаты поиска

Содержание ivizion ld

Отзывы:

Похожие инструкции для ivizion ld

Бренды по названию

Популярные бренды