background image

Time programming

The door must be completely closed before starting time programming.

Press the PANEL PROG button for 1 second to enter programming. The red PRG pilot light will come on and the equipment will

emit an acoustic signal.

Use the START or TEST button to programme the run.

When START/TEST is pressed for the first time, the door will act as follows: Opens slightly, closes to the lower stop, opens to

the upper stop and stops moving. When START/TEST is pressed for the second time, the panel memorizes the automatic

standby time, closes to the lower stop, stops and exits the programming mode (the red pilot light goes out). The opening and

closing time will now have been programmed.

Option switch

ON position

OFF position (default position)

1- DM OP

Dead-man operation: The START button serves as
the Open button

Semi-automatic operation

2- DM CL

Dead-man operation: The TEST button on the board
serves as the Close button

Semi-automatic operation

3- AUTO-TEST OP

This carries out the auto-test for the security open
contact

No auto-test carried out

4- AUTO-TEST CL

This carries out the autot-est for the security open
contact

No auto-test carried out

5- OPEN-STOP-
OPEN

The panel always opens until the end of the opening
time

Alternative operation: open-
stop-close-stop

6- AUTO-CLOSE

Automatic closure

Does not close automatically

7- FLASH

Courtesy light acts as the signal with a 1.5 sec. pre-
warning during door movement

Courtesy light acts as the gar-
age light for 60 sec. after door
movement

Input switch

Option No.

Lower position – OFF

Upper position – ON (default option)

1- SEC.CL

Security Close contact connected

Security Close contact not connected

2- SEC.OP

Security Open contact connected

Security Open contact not connected

3 STOP

Stop button connected

Stop button not connected

Light indicators

POWER

Indicates power

PROG

Indicates programming

SAFETY FiXED

Indicates failure of safety or Radioband element autotest

SAFETY BLINKING

Indicates security edge inhibiting

Lock and end of run detection

The panel includes a function that automatically detects the end of the run or detects when the motor is mechanically blocked,

stopping movement in both cases.

In programming mode, this circuit saves on users having to press START/TEST.

In operating mode, the panel protects the motor in the event of becoming blocked.

The function does not replace sensitive edge protection.

jcm

technologies

6

Содержание EASY-ROLL









Отзывы: