background image

9

JCB-MS-254SB
Instruction & User Manual

Safety instructions for the 

handling of saw blades

 removing the cut-off piece.

 

Only use insertion tools if you have mas-
tered their use.

Observe the maximum speed. The maxi-
mum speed specified on the insertion tool 
may not be exceeded. If specified, observe 
the speed range.

Observe  the  motor  /  saw  blade  direction 
of rotation.

Do not use any insertion tools with cracks. 
Sort out cracked insertion tools. Repairs are 
not permitted.

Clean grease, oil and water off of the clamp-
ing surfaces.

Do  not  use  any  loose  reducing  rings  or 
bushes  for  the  reducing  of  holes  on  saw 
blades.

Make sure that fixed reducer rings for se-
curing the insertion tool have the same di-
ameter and have at least 1/3 of the cutting 
diameter.

Make sure that fixed reducer rings are par-
allel to each other.

Handle  insertion  tool  with  caution.  They 
are ideally stored in the originally package or 
special containers. Wear protective gloves 
in order to improve grip and to further re-
duce the risk of injury.

10 

Prior  to  the  use  of  insertion  tools,  make 
sure that all protective devices are properly 
fastened.

11 

Prior to use, make sure that the insertion 
tool  meets  the  technical  requirements  of 
this electric tool and is properly fastened.

12 

Only use the supplied saw blade for cutting 
wood, never for the processing of metals.

This electric tool generates an 
electromagnetic field during operation. This 
field can impair active or passive medical 
implants under certain conditions. In order to 
prevent the risk of serious or deadly injuries, 
we recommend that persons with medical 
implants consult with their physician and the 
manufacturer of the medical implant prior to 
operating the electric tool.

WARNING!

Reaching with your hand near the 
coasting blade is dangerous.

The braking action of the saw may cause 
the saw head to be suddenly pulled 
downward, causing a risk of injury.

 

 

19

Hold the handle firmly when making 
an incomplete cut or when releasing 
the switch before the saw head is 
completely in the down position.

All manuals and user guides at all-guides.com

Содержание MS-254SB

































Отзывы: