manualshive.com logo in svg

jcb JCB-CS38, Инструкция по безопасности и эксплуатации

Поделиться
Скачать
jcb JCB-CS38 Скачать руководство пользователя страница 18

SO53 3LE
Customer Helpline 0845 600 5526 Monday to Friday 09.00 to 17.00 
www.JCBdiy.com

safety, set the chain brake when the saw is not in use.

iii.  In the event that the ignition switch will not stop the saw, pull the choke lever 

out to the fully extended position “Full choke” and engage the chain brake to 
stop the engine. If the ignition switch will not stop the saw when set to the “Stop” 
position, have the ignition switch repaired before using the chainsaw again to 
prevent unsafe conditions or serious injury.

Note: 

After using the saw, always relieve tank pressure by loosening then re-tight-

ening the chain lubricant and fuel caps. Allow the engine to cool before storing.

ADJUSTING IDLE SPEED

See Figure 15.

 

If the engine starts, runs and accelerates, but will not idle, turn the idle speed screw 

“T”

 clockwise to increase idle speed to 2600~3600 rpm.

 

If the chain turns at idle, turn the idle speed screw 

“T” 

counter clockwise to reduce 

the idle RPM and stop the chain movement. If the saw chain still moves at idle 
speed, contact an authorised service centre for adjustment and discontinue use 
until the repair is made.

 

WARNING

THE SAW CHAIN SHOULD NEVER TURN AT IDLE. Serious personal injury may 
result from the saw chain turning at idle.

PULL AND PUSH

See Figure 16.

The reaction force of the saw is always opposite to the direction the chain is moving. 
The operator must be ready to control the PULL when cutting on the bottom edge of 
the bar and the PUSH when cutting along the top edge.

Note: 

The chainsaw has been factory tested. It is normal to find some slight lubri-

cant residue on the saw.

KICKBACK PRECAUTIONS

See Figures 17-18.

Rotational kickback occurs when the moving chain contacts an object at the Kickback 
Danger Zone of the guide bar. The result is a lightning-fast reverse reaction, which 
kicks the guide bar up and back towards the operator. This reaction can cause loss of 
control, which can result in serious injury.

PREPARING FOR CUTTING 

JCB-CS38_Manual_D1.indd   18

JCB-CS38_Manual_D1.indd   18

11/12/2010   6:44:16 PM

11/12/2010   6:44:16 PM

Содержание JCB-CS38






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды