manualshive.com logo in svg

JC Systems 620A, Справочное руководство

Поделиться
Скачать
JC Systems 620A Скачать руководство пользователя страница 2

 

Model 620A by TMC Services Training 

By Compass Services

 

 

 

The front panel displayed is referred to as the “Home or Run” Screen.

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Overview:  Front Panel displays, and indicators. 

 

1:

  CH1 & CH2 Inc/Dec LED’s.  Indicate “ON/OFF” Time Proportioned output. 

     INC, up arrow (heat, humidify, climb, etc.) and DEC, down arrow (Cool, de-humidify, dive, etc.)     
 

2:

  Displays Program # (1 – 99), Step # (1 – 200), and Time Remaining in current program step. 

 

3:

  Displays Interface, LCL (Local, front panel) or RMT (Remote, external computer) and Mode 

     (RUN, STP, EOP, GS1, GS2, etc.) 
      

4:

  Line 1:  Displays CH1 & CH2 SP (Setpoint) and status of first eight event outputs (1 – 8) 

     Line 2:  Displays CH1 & CH2 PV (Process value) and status of next eight event outputs (A – H) 
 

      (SP and PV are displayed in units configured for that channel (deg C, F, %RH, Alt/FT etc.) 

 

5:

  ALM – 4 possible flashing displays:  S1 – S2 – L1 – L2. 

 

S1 & S2 – Setpoint Alarm.  Setpoint is out of configured controller span or input is open. 

            CH1 or CH2 PV will display “RANGE” setpoint out of range or “P.OP” – Probe Open.  
 
 

L1 & L2 – DEV Limit Alarm. Channel is out of prog/- DEV span. 

            Each channel can be configured for the program to continue running or stop during alarm, 

and for the alarm display and output to reset manually or automatically. 
CH1 & CH2 share a common Logic low output from the 620A. 

 

Содержание 620A










































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды