JBL VTX A8 Series Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 65

background image

13

VTX A

8

| Rigging Manual

5 - SOFTWARE

5.1 - LINE ARRAY CALCULATOR 3

TM

LAC is a simulation software for designing and predicting JBL VTX Series systems. LAC predicts the acoustical performance coverage of
line array systems as well as flown and ground stacked subwoofer arrays. Enhanced acoustical modeling includes color SPL mapping, 0
dB isobar and SPL attenuation modes with the frequency response and SPL based on JBL’s DSP presets. Up to 8 virtual microphones
can be placed in the venue for accurate, position-dependent response prediction. Additionally, subwoofer modeling is now offered.
Subwoofer delay values can be generated for electronic delay steering (EDS) of subwoofer arrays using the built-in calculator.

Beyond the acoustical prediction, LAC is used for mechanical validation of all used suspension hardware. Weight limits are calculated
in real time for single or dual-point suspensions. An array design factor is calculated that can be used for designing an array within local
regulation limits. Safety warning massages are displayed when an unsafe configuration has been selected. Array statistics like array
size, depth and weight are also calculated.

«
...
11
12
13
14
15
...
»

Содержание VTX A8 Series


































































Отзывы:

Нет отзывов

Похожие инструкции для VTX A8 Series

Бренд: K-array Страницы: 8

Бренд: K-array Страницы: 20

Бренд: Samsung Страницы: 29

Бренд: GATmatic Страницы: 16

Бренд: Revox Страницы: 12

Бренд: Clarke Страницы: 24

Бренд: Mirage Страницы: 1

Бренд: Sierra Страницы: 11

Бренд: Videx Страницы: 60

Бренд: EAW Страницы: 2

Бренд: MRC Страницы: 2

Бренд: Ltc Audio Страницы: 24

Visual Performance VP65 SST

Бренд: Sonance Страницы: 4

Power2 S-MIG 100

Бренд: STAMOS Страницы: 33

TRANSPARENT ONE ENCORE PLUS

Бренд: Vanatoo Страницы: 2

Maxstar 150 STL

Бренд: Miller Electric Страницы: 4

Blue Thunder Series

Бренд: Miller Страницы: 36

ISB224 v1065-01

Бренд: iLive Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды