manualshive.com logo in svg
background image

TROUBLESHOOTING

If you are using the Speaker In connections and there
is no sound from any of the speakers, check the
following:

• Receiver/amplifier is on and a source is playing.

• The subwoofer is plugged in to an active AC outlet and turned on.

• Check all wires and connections between receiver/amplifier and

speakers. Make sure all wires are connected. Make sure none of
the speaker wires are frayed, cut or punctured.

• Review proper operation of your receiver/amplifier.

If there is low bass output, check the following:

• Make sure the connections to left and right Speaker In have the

correct polarity (+and –).

• Make sure that the subwoofer is plugged into an active AC outlet

and turned on.

• Select the phase switch setting which provides maximum bass

output at the listening position.

• Adjust the crossover point.

• Adjust the Contour control.

• Turn up the bass with the Level control.

If you used the Line In connections and there is no
sound from the subwoofer, check the following:

• Receiver/amplifier is on and a source is playing.

• The subwoofer is plugged in and turned on.

• Check all wires and connections between receiver/amplifier and

subwoofer. Make sure all wires are connected. Make sure none of
the wires are frayed, cut or punctured.

• Review proper operation of your receiver/amplifier.

If you hear high levels of midrange frequencies from
the subwoofer in addition to bass, check the following:

• Make certain that Filter Defeat is not pressed.

• Try a lower crossover frequency using the Filter control.

TECHNICAL SPECIFICATIONS

TiK Sub

Amplifier Power (RMS): 600 Watts

Driver: 15" Kevlar/Kapoc impregnated cellulose pulp cone

Inputs: Line Level, Speaker Level and DSP Direct

Outputs: Line Level and Speaker Level

Low Pass Frequency: 30 kHz – 150 Hz, 24 dB/octave, continuously
variable

Dimensions (HxWxD): 570 x 440* x 550 cm

Weight: 61 kg.

* The front panel is 440 mm wide. The rear panel is 330 mm wide.

Declaration of Conformity

We, JBL Europe A/S

Kongevejen 194B 
DK-3460 Birkerød
DENMARK

declare in own responsibility, that the products described

in this owner's manual are in compliance with technical

standards:

EN 55 013/6.1990

EN 55 020/6.1988

EN 55 022/6.1993

EN 60 065/1994

EN 60 555-2-3/1987/88

Steen Michaelsen

JBL Europe A/S

Birkerød. DENMARK. 1/97

EN 55013/A12: 1994
EN 55020: 1994
EN 61000-3-2: 1995

We, Harman Consumer International

2, Route de Tours
72500 Château-du-Loir
FRANCE

Steen Michaelsen

JBL Europe A/S

Harman Consumer International

France 11/00

ENGLISH

Содержание TiK Sub















Отзывы: