manualshive.com logo in svg

JBL Ivx HP-DS170, Руководство по установке

Поделиться
Скачать
JBL Ivx HP-DS170 Скачать руководство пользователя страница 5

5

This manual describes the recommended installation 
procedure for the JBL Professional Intellivox HP (High 
Power) series of loudspeakers.

The JBL Intellivox is a type of loudspeaker known as an 
active DSP-controlled loudspeaker array, which utilises 
the principle of mounting multiple, individually-driven 
loudspeaker drive units in the vertical plane at specific 
spacings. In addition to the drive units, the Intellivox 
housing contains a mains-powered electronics module 
containing multiple power amplifier channels and a Digital 
Signal Processing (DSP) section. 

The Intellivox HP series models have been specifically 
designed for applications where a high SPL, and/or an 
extended audio frequency response suitable for high 
quality music reproduction are required.

This manual describes the following aspects of an 
installation: 

•  Necessary cabling 
•  Connector wiring 
•  Mechanical installation

After installation, the amplifier and 
loudspeaker should be tested for basic 
functionality using the supplied JBL 

WinControl software; the manual also describes this 
procedure. (Note that full configuration and control of the 
loudspeaker is beyond the scope of this manual; this topic 
is fully documented in the WinControl Help files.)

APPLICABLE MODELS AND VARIANTS

This manual applies to the following JBL Intellivox models*:

Intellivox HP-DS170 
Intellivox HP-DS370

The HP-DS170 loudspeaker unit is fitted with ten 6.5” low/
mid-range drivers and two 1” hi-frequency compression 
drivers.

The HP-DS370 loudspeaker unit is fitted with fourteen 
6.5” low/mid-range drivers and two 1” hi-frequency 
compression drivers.

2. INTRODUCTION

 *Other models in the Intellivox range, including the DC/DS 115 and DC/DS/DSX 180, 280, 380, 430 and 500, have different 
installation procedures and this manual should NOT be used when installing them. Refer instead to the Intellivox Installation 
Guide applicable to these models.

HP-DS370

HP-DS170

Fig.1 The Intellivox models covered by this manual.

201601/IvxHPDS_v1.2

JBL

®

 Intellivox HP series Installation Manual Rev 1.2

Содержание Ivx HP-DS170



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды