Harman International Industries, Incorporated.
8500 Balboa Blvd, Northridge CA 91329 United States.
European Representative
: Harman International Industries, Incorporated.
EMEA Liaison Office, Danzigerkade 16G, 1013 AP Amsterdam, The Netherlands.
UK Business Address
: Ground Floor, Westside 2, London Road, Apsley, Hemel Hempstead, Hertfordshire, HP3 9TD, United Kingdom.
© 2023 Harman International Industries, Incorporated. All Rights Reserved.
JBL is a trademark of Harman International Industries, Incorporated registered in the United States and other countries.
Features, Specifications, and Appearance subject to change without notice.
DA1650 Quick Start Guide | rev1.3 20231012 | Features, Specifications, and Appearance subject to change without notice.
Pg 2 of 2
WIRING OUTPUT CONNECTORS
Before making any output connections, ensure the power cord is disconnected from the amplifier and carefully review the total impedance for loudspeakers
connected to each amplifier output. If multiple loudspeakers are connected to an output (i.e., in series, parallel, or series-parallel), be certain the total system
impedance is within the allowed specification for the output. See the “Specifications" table below for supported load specifications.
JBL recommends using two-conductor or four-conductor, heavy gauge speaker wire up to 12 AWG.
Speaker outputs provide connection for up to eight pair of stereo speakers (sixteen speakers total)
to the DA1650 via phoenix-type connectors that accept bare wire terminations. The connectors are
grouped in pairs with one connector each for pair.
Each pair consists of four wire terminations: positive (+) and negative (–) for the Left channel and
positive (+) and negative (–) for the Right channel.
To attach speaker cables to the phoenix connector, strip approximately ¼” of insulation from the end of
the positive and negative leads of the cable and insert the bare ends into the corresponding position
of the phoenix connector, tightening the screw terminals on top to secure the termination. Repeat this
procedure for each speaker.
CONNECTING BRIDGED OUTPUTS
1.
Set BRIDGE/MONO as needed for each zone by moving the switch to the UP position for that zone.
2.
Connect the + terminal from the speaker to the + terminal of the left channel on the amplifier.
3.
Connect the – terminal from the speaker to the – terminal of the right channel on the amplifier.
The two terminals for a bridged pair of speakers are marked by + BRIDGED –
In Bridge mode, the pair of amplifier channels in a zone combine to make a mono output of double the
power. When in bridge mode the left and right channel RCA inputs to the zone are active so you can
connect one mono source (Left) or a stereo source (Left and Right) which will sum-to-mono appropriately.
Controls and Adjustments
A
AC power inlet and switch
B
Bridge/Mono mode - Set the switch to the UP position per zone to enable
Bridge/Mono Mode.
C
Link to global input - Set the switch to the UP position to link a zone to the
ZONE 1 INPUT/ GLOBAL INPUT
D
Power mode –
ON: Always On
12V: Controlled by 12VDC trigger.
AUTO: Turn on when an audio signal is sensed on the audio input
E
Output level control – Provides output level attenuation per Zone pair
Specifications
Connectivity and Control
Power
(1kHz, 20ms burst, 2 channels driven, 0.5% THD max)
Analog audio input
16 x RCA (Single Ended)
Rated Power (8Ω)
50W
Stereo analog global output
(global input looped to global
output)
2 x RCA (Single Ended)
Rated Power (4Ω)
110W
Speaker output
Phoenix block connectors
Rated Power
(8Ω Bridged, one zone driven)
185W
12V trigger control
1 x 3.5mm (in)
1 x 3.5mm (out)
Electrical
Power
Standard IEC
Power supply
Universal Mains 100–240VAC 50-60Hz
Global input select
4 x 2-position dip switches
Standby power consumption
Less than 0.5W
Bridge/Mono select
4 x 2-position dip switches
for full specifications)
Power Mode select
1 x 3-position switch