background image

Designed  to  be  unobtrusive,  offer  theft  deterrence, 
and  simplify  the  installers  job,  the  patented  InvisiBall

®

 

mounting system features a unique method for installing a 
loudspeaker onto a wall or other flat surface.  

Installing  this  Commercial  Sound  product  must  be 
done  in  accordance  with  local  building  codes  and 
regulations.  Consult  with  a  licensed  contractor  or 
professional  engineer  regarding  any  installation 
in  which  the  loudspeakers  are  mounted  to  a  wall  or 
ceiling.    For  outdoor  applications,  be  sure  to  use  a 
mounting  support  system  which  has  sufficient  wind 
load strength in accordance with local building codes 
and regulations. JBL Professional is not responsible 
for damages resulting from the negligent installation 
of any bracket or speaker.

1.  Install  the  InvisiBall  mounting  bracket  plate  on  the 
mounting  surface  as  shown  in  Fig.  1. 

Be  sure  to  use 

anchor hardware that is appropriate for the mounting 
surface and that the mounting surface will adequately 
support the loudspeaker assembly. 

2.  Using  a  wide-tipped,  slotted  screwdriver,  remove  the 
plastic InvisiBall knock-out plug by pushing downward as 
shown in Fig. 2. Remove any residual plastic around the 
hole to ensure the ball assembly will fit into the hole.

3. Remove the logo badge on the speaker grill by pulling it 
straight out as shown in Fig. 3.

4. Insert the supplied hex key into the hole exposed by the 
logo badge. Lightly push and slowly rotate the hex key until 
you feel the key fall into place. Loosen the InvisiBall clamp 
as shown in Fig. 4.

5. Mount the speaker on the InvisiBall as shown in Fig. 5.

6. Tighten the clamp just enough to hold the speaker while 
it is positioned in its desired orientation.  When the speaker 
is in the desired direction, tighten the InvisiBall clamp as 
shown in Fig. 6 and replace the logo badge. 
CAUTION: DO NOT OVERTIGHTEN.

INVISIBALL MOUNTING INSTRUCTIONS 

2

JBL Professional Control 25AV-LS

Fig. 2

Fig. 3

Fig. 4

Fig. 5

Fig. 6

Fig. 1

Содержание Control 25AV-LS









Отзывы: