ENGLISH
OPERATION MANUAL
JB SYSTEMS
®
5/36
LED SPOT – LED WASH
OPERATING INSTRUCTIONS
A. Standalone 1unit:
Just connect the unit to the mains and put on some music. The unit starts working automatically to the
rhythm of the music.
Remark:
You can connect a CA-8 remote controller to the unit if you want to have more control.
B. Two or more units in master/slave setup:
Connect 2 to maximum 16 units together. Refer to the chapter “electrical installation” to learn how to
do this (don’t forget to address all units properly!)
Connect all units to the mains and put on some music. The units will start working automatically to the
rhythm of the music and show the internal chase programs.
Remark:
You can connect a CA-8 remote controller to the master unit if you want to have more control
over the master/slave operation.
C. Connect the optional CA-8 controller for more control:
The CA-8 controller can only be used in standalone or master/slave mode. Connect the controller to the
CA-8 input of the first unit (master). Now you can control all the connected units:
IMPORTANT REMARK:
When you use this LED PROJECTOR with a CA-8 controller and you select MANUAL mode (mode
LED = ON), the projector reminds the last setting used with controller, even after disconnecting
the controller and/or the mains voltage. If you don’t want this, make sure to select another
working mode (mode LED must blink or off) before you unplug the controller.
Placed on a horizontal
surface
Fixed to wall or
ceiling
Fixed to ALU-truss
BUTTON
ACTIONS
STANDBY
To blackout all the fixtures
FUNCTION
Strobe
1.Synchronous strobe
in white color
2.The same color
chase
3.Differentcolor
strobe
9 Color select
White
Red
Blue
Purple
Orange
Green
Yellow
Magenta
Cyan
Color Chase
1. The same color
2. Different color
3. One light chase
4. Two lights chase
5. Four lights chase
Color Fade
1. Fast speed
2. Middle speed
3. Slow speed
MODE
Sound 1
(LED OFF)
Manual
(LED ON)
Sound 2
(LED slow blinking)
Auto
(LED fast blinking)
ENGLISH
OPERATION MANUAL
JB SYSTEMS
®
6/36
LED SPOT – LED WASH
D. Controlled by universal DMX-controller:
Connect all units together. Refer to the chapter
“Electrical installation for two or more units in
DMX-mode” to learn how to do this (don’t forget
to address all units properly!)
Connect all units to the mains and turn on the
DMX controller.
Since each unit has its own DMX-address, you
can control them individually. Remember that each
unit uses 4 DMX-channels as shown in the DMX
chart below:
MAINTENANCE
Make sure the area below the installation place is free from unwanted persons during servicing.
Switch the unit off and unplug the mains cable.
During inspection the following points should be checked:
All screws used for installing the device and any of its parts should be tightly fastened and may not be
corroded.
Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any
deformation.
When an optical part is visibly damaged due to cracks or deep scratches, it must be replaced.
The mains cables must be in impeccable condition and should be replaced immediately when even a
small problem is detected.
The interior of the device should be cleaned annually using a vacuum cleaner or air-jet.
The cleaning of internal and external optics must be carried out periodically to optimize light output.
Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly
dirty surroundings can cause greater accumulation of dirt on the unit’s optics.
Clean with a soft cloth using normal glass cleaning products.
Always dry the parts carefully.
Clean the external optics at least once every 30 days.
Clean the internal optics at least every 90 days.
Attention: We strongly recommend internal cleaning to be carried out by qualified personnel!
