![background image](http://html1.mh-extra.com/html/jayco/kiwi-travel-trailer-2003/kiwi-travel-trailer-2003_owners-manual_3645346017.webp)
25
24
Electric
EXTENDING ROOM
1. The batteries must be fully charged and connected. The travel trailer should be
hooked up to 120-volt AC power if possible.
2. The travel trailer must be level and the stabilizer jacks in the down position.
1
CAUTION:
Additional support jacks are not needed
under the slideout. Damage can occur to your slideout room from improper
use of support jacks.
3. Remove the “travel bars” (Fig. 3-13) from behind the top
facia board located above slideout room.
4. Locate the slideout room control switch. (Fig. 3-15)
5. To move the room out, press the “OUT” button on the switch
(Fig. 3-15) and hold it until the motor stops. Release the
button. Travel time – approximately twenty-five seconds.
RETRACTING ROOM
1. Remove all objects left between the slideout and cabinetry.
2. Press the “IN” button to bring the room in and hold it until
the motor stops.
3. Release the button.
4. Install “travel bars” (Fig. 3-13) in proper locations as indicated on the wall.
1
CAUTION: IMPORTANT! Never store slideout without the travel bars
installed. This helps seal the slideout in the closed position.
Getting Connected
Upon completing the setup of your travel trailer, you are now ready to make attachments
to various facilities as listed but not limited to:
1. Fresh water supply.
2. Waste water hose connection(s).
3. 120-volt power cord electrical hookup.
4. Turn on the LP gas tanks and light pilot lights for any appliances. Remember there
may be air in your LP propane lines. Be sure to bleed them before planned usage.
5. Open any windows and roof vents as desired for ventilation.
You may have additional accessories and options, such as an awning on door side, which
need to be opened. Separate instructions are provided by the manufacturer of these
component.
1
CAUTION:
When preparing to depart or move, reverse the procedure
above. Remember, open roof vents, windows, TV antennas left in up position
are subject to wind damage in transit.
See the process to follow before departing from your campsite under the hitching
procedures listed earlier in this chapter.
5. Enter the unit and push the bed mats out
onto the bed board. Position the large
mat out to the furthest edge of the bed
board. Slide the small mat toward you
lining up the velcro pieces to hold it in
place. (Fig. 3-12)
6. Place the straight end of the bed bow
support pole onto the bed
bow brace connector (on
the bed bow). (Fig. 3-11)
Push the bed bow outward
and upward while pressing
the second button from the curved end of the bed bow support pole.
Slip the pole into the bracket mounted on the roof just past the first
button. Release the button.
7. Remove the canvas straps and store them under the front edge of the small bed mat.
SLIDEOUT ROOM OPERATION (SLIDEOUT MODELS ONLY)
Manual
EXTENDING ROOM
1. Release the travel lock (Fig. 3-13) behind the cen-
ter door of the overhead cabinets located above the
sofa.
2. Lift the sofa skirt. Install the crank handle on the
hex head screw as indicated (Fig. 3-14) and crank
the system out, turning the handle in a clockwise
direction until the room is extended.
3. Remove the handle and store it for use later.
RETRACTING ROOM
1. Lift sofa skirt.
2. Install the crank handle and turn it in a counter-clockwise direction to retract the
slideout.
3. Lock top travel lock.
Fig. 3-11
Fig. 3-13
Fig. 3-14
Fig. 3-15
Fig. 3-12
Содержание Kiwi Travel Trailer 2003
Страница 8: ...7 6 CHAPTER 2 OBTAINING SERVICE WARRANTY REGISTRATION S A M P L E S A M P L E...
Страница 53: ...97 96 NOTES LIMITED WARRANTY TRANSFER cont SAM PLE...
Страница 54: ...98 NOTES...