Jayco Conventional Travel Trailer 2003, Руководство пользователя

Страница: 52 / 64

93 92
STORAGE
Depending upon your area and where your unit is stored, your camper may be a target for
damage from rodents and insects. To protect your camper, never leave food inside the
unit and ensure that all surfaces are clean. You may want to place rodent control products
in the unit during periods of storage. Mice can do a tremendous amount of damage to the
tent, drapes, cushions, etc. particularly during the winter months. Storing units in fields
make them particularly inviting to rodents. Periodically inspect your unit during storage
and seal off any areas which can offer an entry point to rodents or insects. Please
remember to remove any screens or tape you have used to seal openings before you use
the camper again. Special interest publications, such as articles and books offered
through TL Enterprises (Trailer Life, Motorhome, etc.) can offer additional and practical
advice on the proper storage of your camper. Damage from rodents or insects are NOT
covered under your Jayco Limited Warranty.
1
CAUTION: When storing your travel trailer, it is recommended that the
battery be unhooked to avoid draining the battery.
LP GAS BOTTLES
1. The LP gas bottle or tank must be painted with a light color, such as white or silver
plate, to reflect heat and light.
2. Rust, scratches, and/or dents can affect the safety of the bottle or tank. The D.O.T.
requires that a visual inspection is made prior to each filling.
3. Any container that has been exposed to fire, leaks or seems damaged should not be
refilled.
4. An LP bottle must always be placed in an upright position. Assure that the bottle is
secured in place prior to moving the vehicle.
5. The D.O.T. requires that LP bottles be inspected, certified and labeled when it is
twelve years old. (The number of years for certification may vary in your area.)
Following the initial twelve-year period, the bottle must be certified every five years.
6. The valve of the bottle or tank must be CLOSED at all times except when it is
connected to the recreation vehicle LP gas system or is being refilled.
7. Inspect the bottle at regular intervals. If there is a problem, have it evaluated by a
qualified technician and discard it, if necessary. Verify with your local LP dealer
that all required inspections and certifications have been completed on the LP bottle
within the correct time period before refilling the bottle.
E-Z LUBE AXLE
If your axle is equipped with the E-Z Lube feature, the bearings can be periodically
lubricated without removing the hubs from the axle. This feature consists of axle
spindles that have been specially drilled and fitted with grease zerk in their ends. When
grease is pumped into the zerk, it is channeled to the inner bearing and then flows back
to the outer bearing and eventually back out the grease cap hole.
LUBRICATION PROCEDURES (FIG. 7-4):
1. Remove the rubber plug from the end of the grease cap.
2. Place a standard grease gun onto the grease zerk located in the end of the spindle.
Make sure the grease gun nozzle is fully engaged on the fitting.
3. Pump grease into the zerk. The old, displaced grease will begin to flow back out the
cap around the grease gun nozzle.
4. When the new, clean grease is observed, remove the grease gun, wipe off any
excess, and replace the rubber plug in the cap.
5. Rotate the hub or drum while adding grease.
NOTE: The E-Z Lube feature is designed to allow immersion. Axles not equipped
with E-Z Lube are not designed for immersion and bearings should be
repacked after each immersion. If hubs are removed from an axle with the
E-Z Lube feature, it is imperative that the seals be replaced BEFORE bearing
lubrication. Otherwise, the chance of grease getting on brake linings is
greatly increased.
NOTE: The convenient lubrication provisions of the E-Z Lube and the oil lubrication
must not replace periodic inspection of the bearings.
Fig. 7-4