25
24
1
CAUTION: After the slideout is extended, verify
that the corners of the black rubber seal are set up
correctly. The corners of this seal are cut at a 45ee angle.
The top of the seal must overlap the side of the seal to avoid
the possiblity of water penetration. (Fig. 3-6)
Manual Operation (Qwest Travel Trailer)
EXTENDING ROOM
1. Release the travel lock (Fig. 3-7) behind the center
door of the overhead cabinets located above the
sofa.
2. Lift the sofa skirt. Install the crank handle on the
hex head screw as indicated (Fig. 3-8) and crank
the system out, turning the handle in a clockwise
direction until the room is extended.
3. Remove the handle and store it for use later.
RETRACTING ROOM
1. Lift sofa skirt.
2. Install the crank handle and turn it in a counter-clockwise direction to retract the
slideout.
3. Lock top travel lock.
Electric Operation
EXTENDING ROOM
1. The batteries must be fully charged and connected. The travel trailer should be
hooked up to 120-volt AC power if possible.
2. The travel trailer must be level and the stabilizer jacks in the down position.
1
CAUTION:
Additional support jacks are not needed under the slideout.
Damage can occur to your slideout room from improper use of support jacks.
3.
For Eagle and Qwest models, remove the “travel bars”
(Fig. 3-7) from behind the top facia board located above
slideout room.
4. Locate the slideout room control switch.
5. To move the room out, press the “OUT” button on the switch
(Fig. 3-9) and hold it until the motor stops. Release the
button. Travel time – approximately twenty-five seconds.
RETRACTING ROOM
1. Remove all objects left between the slideout and cabinetry.
2. Press the “IN” button to bring the room in and hold it until the motor stops.
3. Release the button.
4.
For Eagle and Qwest models, install “travel bars” (Fig. 3-7) in proper locations
as indicated on the wall.
1
CAUTION: IMPORTANT! Never store slideout without the travel bars
installed on the Eagle and Qwest models. This helps seal the slideout in the
closed position.
Troubleshooting Electric Slideout
If the slideout does not move when the slideout switch is depressed, follow these steps.
1. Check the battery for a full charge and good wire connections.
2. Check for loose connections at the slideout motor.
If the slideout still will not operate, follow these steps.
1. If the slideout is extended, see the section on overriding the electric slideout system.
2. If the slideout is retracted, leave it in that position. (On Eagle and Qwest models,
install the “travel bars.”)
3. Take the trailer to the nearest dealer or service center.
If the slideout extends crooked, or only one side moves, follow these steps.
1. Follow steps 1 & 2 in the section on overriding the slideout system to disconnect the
motor.
2. Retract the slideout using a 3/4” socket and rachet. You may need to push the side
that is not sliding to get it to retract all the way.
3. Once the slideout is fully retracted, install the “travel bars” on the Eagle and Qwest
models.
4. Take your travel trailer to nearest the dealer or service center.
Overriding the Electric Slideout System
If the system will not move when the switch is pressed, check the following:
• Is the battery connected and does it have a full charge?
• Are the travel bars removed (on the Eagle and Qwest models)?
After checking the above, follow these steps to move the slideout manually.
Tools required:
• ScruLox head screwdriver (if trailer has an underbelly)
• 1/2" wrench
• Adjustable wrench or rachet and 3/4” socket.
Fig. 3-8
Fig. 3-9
Fig. 3-6
Fig. 3-7
Содержание Conventional Travel Trailer 2003
Страница 9: ...7 6 CHAPTER 2 OBTAINING SERVICE WARRANTY REGISTRATION SAM PLE SAM PLE ...
Страница 61: ...111 110 NOTES SAM PLE ...
Страница 62: ...113 112 NOTES NOTES ...
Страница 63: ...114 NOTES ...
