manualshive.com logo in svg

Jay-Lor 31000, Руководство оператора

Поделиться
Скачать
Jay-Lor 31000 Скачать руководство пользователя страница 28

JAY

•

LOR

 Operator’s Manual

  

- 27 -

 

Trailer Units - Model 3875/31000

 

 

 
 

 
 
 
 

ATTACHING/UNHOOKING 

 
The machine should always be parked on a level, dry area that is free of debris and foreign 
objects. 
 
Follow this procedure when attaching: 
 
1.  Clear the area of bystanders and remove foreign objects from the machine and working 

area. 

2.  Make sure there is enough room to back the tractor up to the hitch point. 
3.  Start the tractor and slowly back it up to the hitch point. 
4.  Stop the tractor engine, place all controls in neutral, set park brake, and remove ignition 

key before dismounting. 

5.  Adjust the length of the drawbar to give the appropriate dimension between the PTO 

shaft and drawbar pin hole.  (Refer to Tractor Operator’s Manual). 

6.  Use the clevis on the hitch to level the machine. 
7.  Use the jack to raise or lower the hitch pole to allign with the drawbar. 
8.  Install the drawbar pin with provisions for a mechanical retainer such as a ‘Klik’ pin.  

Install the retainer. 

9.  Attach safety chain between the machine and the tractor drawbar cage. 
10.  Connect the PTO shaft: 

•

 

Check that the PTO driveline telescopes easily and that the shield rotates freely. 

SHIFTER

Figure 9 - 2-speed Transmission Operation. 

Содержание 31000























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды