manualshive.com logo in svg

Jay-Lor 31000, Руководство оператора

Поделиться
Скачать
Jay-Lor 31000 Скачать руководство пользователя страница 24

JAY

•

LOR

 Operator’s Manual

  

- 23 -

 

Trailer Units - Model 3875/31000

 

 

CONTROLS 

Weighing 

 
The scale system on standard 
models includes (3) weighbars.  
The 

walking beam 

system 

incorporates two weighbars while 
the tongue and hitch system 
incorporates the third weighbar.  
The weighbars electronically 
measure the amount of ration 
inside of the mixing chamber. 
 
There are various scale indicators 
available for use on your 
JAY

•

LOR

 

Cutter-Mixer-Feeder. 

The mounting assembly for most 
Weigh-tronix

  Scale Indicators is 

the same.  When attaching the 
indicator to the machine, be sure 
that it is securely fastened.  
Typically, the indicator slides down 
into the mounting bracket, and it is 
also necessary to use a wire or 
plastic fastener to secure the 
indicator to the mounting bracket.  
For more information on mounting, 
refer to the Weigh-tronix

  manual 

included in this binder. 
 
 
 
 
 
 
 
 
 
 
 
 
Most scale options configured in trailer applications use a single scale indicator.  The scale 
indicator is located on the front side of the upper machine frame.  The mounting bracket 
assembly allows the scale indicator to be turned to face every direction. 
 
 
 
 

Note:   

Once the desired position of the scale indicator is set, ensure that the mounting 
bracket  arm  assembly nuts  are  tightened firmly to secure the bracket to the 
machine. 

Figure 5 - 3-point Scale System 

Tongue Bar and Walking Beam System Bars. 

Содержание 31000























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды