background image

www.javad.com

  

9

MODULATION TECHNIQUE

Spread Spectrum (SS) radio transceiver uses two bands: 902-928 MHz ISM license free USA band and Europe-

an CEPT license free 868-870 MHz band. In 902-928 MHz band SS radio uses frequency hopping transmission 

techniques. The design is based on high-level modulation techniques which include:

Modulation/ Channel Spacing

902.0-928.0

GMSK – Minimal Shift Keying with Gaussian Filtering

64.0 kbps, 128 *200.0 kHz

The following are its key benefits:

•  Ten optimized Frequency Hopping Patterns provides simultaneous operating of several units with min-

imum of mutual interference. 

•  FEC coding scheme used with GMSK modulation is based on Convolutional code and the Viterbi decoding 

algorithm which is the most resource-consuming, but it does Maximum likelihood decoding. 

In 868-870 MHz band the design is based on high-level modulation techniques which include:

Modulation/ Channel Spacing

12.5 kHz

25 kHz

GMSK – Minimal Shift Keying with Gaussian Filtering

4.8 kbps

9.6 kbps

The following are its key benefits:

•  FEC coding scheme used with GMSK modulation is based on Convolutional code and the Viterbi decoding 

algorithm. 

•  Powerful FEC scheme used with ArWest proprietary frame format improves the tolerance to interference 

and ensures the highest link quality at distances range higher than 8 miles (13 km) and roaming speeds of 

up to 60 mph (96 km/h).

MANAGEMENT TOOLS

The built-in management tools along with ModemVU (configuration and monitoring software application) will 

provide the following benefits:
1.  Easy user’s interface for system configuration and monitoring using well developed CLI .
2.  An ability to monitor status, alarms and radio performance through the CLI.
3.  Software upgrades and improvements can be downloaded from ModemVU to the units connected with 

PC/PDA.

SECURITY

The system provides wireless media access protection as well as data scrambling. The following are its key 

features and benefits:
1.  The Key Sequence generated by Pseudo-random generator scrambles the fully formatted frame (including 

Frame’s CRC). This provides the wireless media access protection.

2.  User selectable Frequency Hopping Pattern provides another level of the wireless media access protec-

tion.

At the same time it allows operators to increase the number of links deployed in the same location.

Содержание UHFSSRx
























Отзывы: