background image

www.javad.com

  

19

DCRC [Parameters List]

Parameter 

List

Short description

0 - received data are distributed to the port, 

regardless of the received data CRC.  (a default 

setting)

1

1 - data are distributed to the port only if the 

CRC is correct.

The DCRC command without Parameter prints DCRC 

parameter.

DLNG

The DLNG (“Data Subpackage Length”) command 

enables the validation of the receipted parameter - 

length of subpackage.

DLNG [Parameters List]

Parameter 

List

Short description

0

0 - validation of the receipted parameter length 

subpackage is not used   (a default setting).

1

 1 - validation of the parameter is used

The DLNG command without parameter prints DLNG 

parameter.

DSRV

The DSRV (“Data Service”) command allows the 

transmitter to control the tuning of the receiver. 

When DSRV = 1 the receiver settings - FEC, SCRAM, 

TRFC - transmitted from the transmitter to the receiv-

er through the air. 

DSRV [Parameters List]

Parameter 

List

Short description

0

0 - the receiver's parameters are set from the 

configuration file. (a default setting)

1

1 – FEC, SCRAM, TRFC are set from service data 

passed to the receiver through the air.

The DSRV command without parameter prints DSRV 

parameter.

LBT

The LBT (“Listen Before Talk”) command allows to 

verify the channel occupancy before subpackage 

transmitting. If the channel was occupied at the pre-

vious slot, the current slot is not used for data trans-

mission. 

LBT [Parameters List]

Parameter 

List

Short description

0

0 - Listen Before Talk mode is turned off.

1

1 -  Listen Before Talk mode is enabled. (a default 

setting)

The LBT command without parameter prints LBT pa-

rameter.

WHT

The WHT command defines type of data. 

WHT [Parameters List]

Parameter 

List

Short description

43

43 - The receiver sees the received data as Com-

mand.

44

44 - The receiver sees the received data as Data. 

(a default setting)

The WHT command without parameter prints WHT 

parameter.

SRC

The SRC command defines “address” of data (the 

data source code). By defaults SRC coincides with the 

last three symbols of the transmitter SN, but can be 

reprogrammed.

SRC [Parameters List]

Parameter 

List

Short description

XXX

XXX -  the data source code (three hex symbols).

The SRC command without parameter prints SRC 

code.

DST

The DST command defines destination “address” 

of data. Destination address corresponding to the 

source code of the recipient.

DST [Parameters List]

Parameter 

List

Short description

XXX

XXX -  the data destination code (three hex 

symbols).

The DST command without parameter prints DST 

code.

KNW

The KNW command defines the code of the certified 

data source. 

Содержание UHFSSRx
























Отзывы: