background image

16                                                                                                                                                                                       

www.javad.com

BITS =8

PARITY =NONE

FLOW =HARDWARE

STOPBIT =0

DTR =0

RS =RS232

DATATX =UART

DATARX =UART

BUF =0

MPORT

The MPORT is an object that responsible for main-

tenance serial port interface configurations such as 

data rate and number of bits in a byte.

MPORT [Parameter Name] [Parameters List] [/?]

Parameter 

Name

Parameter List

RATE

0 – Auto

1 – 1200 baud

2 – 2400 baud

3 – 4800 baud

4 – 9600 baud

5 – 14400 baud

6 – 19200 baud

7 – 38400 baud

8 – 57600 baud

9 – 115200 baud, a default setting

Note: 

JAVAD GNSS radio modem’s does not support data 

flow and parity on the maintenance serial port. The radio mo-

dem with none-dedicated maintenance serial port must keep 

CTS line always active in MPORT mode (DP/MP is low).

Special Commands

BOOT

The factory software image and default configuration 

is set for the new unit. The BOOT command is intend-

ed to reboot the unit using specified software image 

and selected configuration.

BOOT IMAGE BOOT CFG

The BOOT command with no parameters selects the 

user settings defined by the prior “parameterized” 

BOOT commands.

HELP

The HELP command types the list of all available 

commands:

HELP- Display this usage 

BOOT- Reboot the unit

LINK- Set RF Link Operation Mode 

DPORT- Set Data Port Configuration

MPORT- Set Maintenance Port Configuration

ALARM- Alarm Indication and Alarm Control Con-

figuration SLEEP- Set Sleep Mode Configuration

STATE- Display Status and Statistics

SAVE- Save Current Configuration into Config-

uration File

INFO- Display Product ID along with Hardware/

Software Versions 

ATI- Display Product ID along with Hardware/

Software Versions 

MAP- Operates with Channel Map

DATAMODE- Exit Command Mode

[COMMAND] /?- Display Command Usage

SAVE

The SAVE command is intended to store the unit’s 

currently used configuration into the User Configura-

tion file. The configuration stored in the User Config-

uration file is activated by automatically after unit’s 

reboot.

SLEEP

The SLEEP command determines the sleep mode pa-

rameters. The sleeping AW435BT can be activated by 

real-time CLK, DTR/RTS lines, and command received 

through TTL inputs. The user can select one, two, or 

all three conditions.

SLEEP [Parameter Name] [Parameters List] [/?]

Parameter 

Name

Parameter List

CLK

0 – Do not activate by internal real-time clock

(1 – 255) – Activate by internal real-time clock 

after 100 to 25500 msec of sleeping

HW

0 – Do not activate through DTR/RTS lines 

1 – Activate through DTR/RTS lines

TTL

0 – Do not activate by external sense lines 

1 – Activate by external sense lines

GTS

0 – Disable Sleep mode (default)

(1 – 255) – Go to sleep mode if there is no activity 

in 10 to 2550 msec

Содержание UHFSSRx
























Отзывы: