background image

Jason International, Inc.  •  

 

501.771.4477  

 

 

 

Page 2 of 25

 

 

 

 

Customer Service :  800.255.5766 

Copyright © 2018 Jason International, Inc.

IMPORTANT SAFETY INSTRUCTIONS

INSTRUCTIONS PERTAINING TO THE RISK OF FIRE, ELECTRIC SHOCK, OR 

INJURY TO PERSONS.

This manual contains information and instructions for proper operation and maintenance of your therapy bath. Failure to follow these 
instructions could result in personal injury, electrical shock, or fire.

WARNING: When using this unit, basic precautions should always be followed, including the following:

READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY

DANGER:  TO REDUCE THE RISK OF INJURY FOLLOW THESE PRECAUTIONS:

A. DANGER: 

To reduce the risk of injury, do not permit children to use this unit unless they are closely supervised at all times.

B.  Use this unit only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
C.  The water in a therapy bath should never exceed 104°F (40°C). Water temperatures between 100°F (38°C) and 104°F (40°C) are  
   considered safe for a healthy adult. Use time should be limited to approximately 30 minutes, followed by a shower to cool down.  
 

Longer exposures may result in hyperthermia. 

D.  Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body tempera 
 

ture of 98.6°F (37°C). The symptoms of hyperthermia include an increase in the internal temperature of the body, dizziness, leth 

 

argy, drowsiness, and fainting. The effects of hyperthermia include:

 

a) Failure to perceive heat;

 

b) Failure to recognize the need to exit the hydromassage bathtub;

 

c) Unawareness of impending hazard;

 

d) Fetal damage in pregnant women;

 

e) Physical inability to exit the hydromassage bathtub; and

 

f) Unconsciousness resulting in the danger of drowning.

WARNING – The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia

E.   The use of drugs or alcoholic beverages before or during therapy bath use may lead to unconsciousness with the possibility of  
    drowning. Never use the therapy bath while under the influence of alcohol, anticoagulants, stimulants, antihistamines, vasoconstric 
    tors, vasodilators, hypnotics, narcotics, or tranquilizers.
F.   Lower water temperatures are recommended for extended use (exceeding 10 -15 minutes) and for young children.
G.  Since excessive water temperatures have a high potential for causing fetal damage during the early months of pregnancy,   
 

pregnant or possibly pregnant women should limit therapy bath water temperatures to 100°F (38°C).

H.  Persons with a medical history of heart disease, low or high blood pressure, circulatory system problems, or diabetes should  
 

consult a physician before using a therapy bath.

I.    Persons using medication should consult a physician before using a therapy bath since some medication may induce drowsiness  
    while other medication may affect heart rate, blood pressure, and circulation.

DANGER: 

To reduce the risk of injury, enter and exit the bath slowly.

 Do not operate this unit unless the suction cover is at-

tached over the suction inlet fitting and the jet assemblies are installed. There should be at least two (2) inches of water above the high-
est jet location during therapy bath operation. 

NEVER RUN UNIT DRY.

WARNING:

 Never operate electrically connected devices in or near the bath. Never drop or insert any object into any opening.

This unit must be connected to a supply circuit that is protected by a GFCI. Such a device should be installed by a licensed electri-
cian and should be tested on a regular basis (at least monthly). To test the GFCI push the 

TEST

 button. The GFCI should interrupt the 

power.
Push the 

RESET

 button and the power should be restored. If the GFCI fails to operate in this manner, there is the possibility of an elec-

tric shock. 

DO NOT USE

. Disconnect the unit and have the problem corrected by a qualified service technician.

To avoid the possibility of personal injury and discoloration of the acrylic surface, the inlet water temperature should not exceed 40°C 
(104°F). The bath should be drained after each use. Each bather should start their bath with fresh water. Do not use oil base additives 
in your therapy bath.

CAUTION: 

Do not use harsh abrasives or solvents for cleaning this unit.

INSTALLER/OWNER BEARS ALL RESPONSIBILITY TO COMPLY WITH ALL STATE AND

LOCAL CODES WHEN INSTALLING THIS PRODUCT

SAVE THESE INSTRUCTIONS

Содержание MicroSilk


























Отзывы: