REX F-1-9 and REX F-3-9 – Standalone or Access Controller
3/2015
Black line
www.jantar.si
Function 4) Pre-alarm and alarm
Set the pre-alarm time. This is the time in which the controller, with short
beeps, alerts you that the door was left open. If you don’t close the door in
the pre-alarm time, the alarm will be triggered and signaled with long beeps
by the controller. The time can be set in seconds or minutes. Switching time
from seconds to minutes and back, can be adjusted by using the function 15.
Set the pre-alarm time with master fingerprint:
Place the master fingerprint four times on the sensor and remove it (4
double beeps). The controller will start to beep every second. Each beep
indicates 1 second or 1 minute of the pre-alarm time. Duration of the pre-
alarm time can
be max 120 seconds or 60 minutes. When you hear the
required number of beeps, place a user fingerprint on the sensor
or approach
a user card for confirmation.
Set the pre-alarm time with master card:
Approach the master card and remove it after 4 double beeps. The controller
will start to beep every second. Each beep indicates 1 second or 1 minute of
the pre-alarm time. Duration of the pre-alarm time can
be max. 120 seconds
or 60 minutes. When you hear the required number of beeps, approach a
user card
or place a user fingerprint on the sensor for confirmation.
Function 5) Negate / Switch output state
This function is used, when you connect an electric strike or electric magnet
which needs power supply to remain in locked state.
Switch output state with master fingerprint:
Place the master fingerprint five times on the sensor and remove it (5 double
beeps). Within a period of three seconds place a user fingerprint on the
sensor or approach a user card. The output state will be switched from the
current one.
Switch output state with master card:
Approach the master card and remove it after 5 double beeps. Within a
period of three seconds approach a user card or place a user fingerprint on
the sensor. The output state will be switched from the current one.
Function 6) Delete a fingerprint or a lost card
Delete the next fingerprint or card on the list. Use this function if you wish to
delete a fingerprint or lost card from the controller. In order to use this
function you must maintain a list of registered fingerprints and cards,
arranged by order of registrations so that you can find the fingerprint or
card, which was registered before the one you wish to delete.
Delete a fingerprint or a lost card with master fingerprint:
Place the master fingerprint six times on the sensor and remove it (6 double
beeps). Within a period of three seconds place a user fingerprint on the
sensor or approach a card, which was registered
before
the one you wish to
delete. This will delete the next fingerprint or card on the list. Next
registered fingerprint or card will take the position of a deleted fingerprint or
deleted card.
Delete a fingerprint or a lost card with master card:
Approach the master card and remove it after 6 double beeps. Within a
period of three seconds approach the user card or place a user fingerprint on
the sensor, which was registered
before
the one you wish to delete. This will
delete the next fingerprint or card on the list. Next registered card or
fingerprint will take the position of a deleted card or deleted fingerprint.
Function 7) Delete a fingerprint or a lost card
Delete the previous fingerprint or card on the list. Use this function if you
wish to delete a fingerprint or lost card from the controller. In order to use
this function you must maintain a list of registered fingerprints or cards,
arranged by order of registrations so that you can find the fingerprint or
card, which was registered after the one you wish to delete.
Delete a fingerprint or a lost card with master fingerprint:
Place the master fingerprint seven times on the sensor and remove it (7
double beeps). Within a period of three seconds place a user fingerprint on
the sensor or approach a card, which was registered
after
the one you wish
to delete. This will delete the previous fingerprint or card on the list. Next
registered fingerprint or card will take the position of a deleted fingerprint or
deleted card.
Delete a fingerprint or a lost card with master card:
Approach the master card and remove it after 7 double beeps. Within a
period of three seconds approach the user card or place a user fingerprint on
the sensor, which was registered
after
the one you wish to delete. This will
delete the previous fingerprint or card on the list. Next registered card or
fingerprint will take the position of a deleted card or deleted fingerprint.
Function 9) Switch to Wiegand 26-bit, access controller or
back to standalone controller
Switch the controller to a Wiegand 26-bit reader or an access controller. To
change the controller back to a standalone controller from an access
controller, you need to make a “brainwash” with the Codeks or Codeks
Device Manager software.
Switch with master fingerprint or master card:
Place the master fingerprint nine times on the sensor and remove it (9
double beeps) or approach the master card and remove it after 9 double
beeps. The controller will start to beep every second. Each beep presents a
different function, which is selected with a user fingerprint or user card.
Standalone controller
– Place the user fingerprint on the sensor or
approach a user card before 1 beep.
Wiegand 26-bit reader
– Place the user fingerprint on the sensor or
approach a user card after 1 beep.
Access controller
– Place the user fingerprint on the sensor or approach a
user card after 4 beeps.
Function 13) Delete all
Reset/ delete all data to default.
Delete all with master fingerprint:
Place the master fingerprint thirteen times on the sensor and remove it (13
double beeps). The controller will start to beep every second. After three
beeps place a user fingerprint on the sensor or approach a user card for
confirmation.
Delete all with master card:
Approach the master card and remove it after 13 double beeps. The
controller will start to beep every second. After three beeps approach a user
card or place a user fingerprint on the sensor for confirmation.
Delete all with the Codeks Device Manager program:
Set the Rex to the default settings by using the Codeks Device Manager
program. Connect the Rex via RS485 communication line to the Spider
(communication converter, USB or NET). Connect the Spider to the
computer. In Codeks Device Manager, find the device and perform the "Brain
Wash" function which sets the device to its default settings.
Default settings
A three-second pulse, five-second open time, four-second pre-alarm time,
door status switch input and push button input have NO contact; output is
set for fail secure el. strike. The controller is in standalone mode.
Function 15) Sound, alarm output, door status switch input
(NC or NO), set the time in minutes or seconds (function 2,
3, 4)
Turn on/off the sound (beep) which is heard as a pre-alarm and alarm, when
a user fingerprint or user card is registered.
Turn on/off the accelerometer which triggers the alarm output (output1, O1,
wire 4) when the controller is moved.
Set the Input0/I0/wire 5 to normally closed (NC) or normally opened (NO,
default).
Set the time in functions 2, 3, 4 in minutes or seconds.
Set with master fingerprint or master card:
Place the master fingerprint fifteen times on the sensor and remove it (15
double beeps) or approach the master card and remove it after 15 double
beeps. The controller will start to beep every second. Each beep presents a
different function, which is selected with a user fingerprint or user card.
Beep
Specification
No beep
Sound is OFF
Tamper is OFF
Door status switch input-normally opened (NO)
Time is set in seconds
1. beep
Sound is ON
Tamper is OFF
Door status switch input-normally opened (NO)
Time is set in seconds
2. beep
Sound is OFF
Tamper is ON
Door status switch input-normally opened (NO)
Time is set in seconds
3. beep
Sound is ON
Tamper is ON
Door status switch input-normally opened (NO)
Time is set in seconds
4. beep
Sound is OFF
Tamper is OFF
Door status switch input-normally closed (NC)
Time is set in seconds
