Janome DC 3018 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 33

Janome DC 3018 Скачать руководство пользователя страница 23

PRINTED CIRCUIT

BOARD "F"

SETSCREW

SETSCREW

PRINTED CIRCUIT

BOARD "A"

TO REMOVE:

1. REMOVE THE FRONT COVER (SEE PAGE 9 ~ 10).

2. UNPLUG THE CONNECTORS FROM THE BOARD "A".

3. REMOVE THE 6 SCREWS AND REMOVE BOARD "A".

NOTE: TO DISCONNECT THE CONNECTORS:

1. GRASP THE CONNECTOR DIRECTLY WITH YOUR FINGERS AND PULL. DO NOT PULL ON THE LEAD

WIRE, AS THIS MAY DAMAGE THE CONTACT SLEEVE INSIDE THECONNECTOR.

2. WHEN DISCONNECTING THE MACHINE SOCKET AND POWER TRANSFORMER CONNECTORS, PULL

THEM WHILE PUSHING THEM TOWARD THE A BOARD TO UNLOCK THEM.

TO INSTALL:

4. TO INSTALL, FOLLOW THE ABOVE PROCEDURE IN REVERSE.

NOTE

WHEN INSTALLING BOARD "A" IN THE MACHINE.

THE TRANSFORMER WIRE SHOULD NOT PASS OVER THE CAPACITOR WHEN BOARD "A" IS

INSTALLED.

IF THE CORD IS RESTING ON THE CAPACITOR, IT MAY INTERFERE THE PATTERN SELECTOR

BUTTON AFTER THE FRONT COVER IS INSTALLED.

REPLACING PRINTED CIRCUIT BOARD A

SETSCREW

SETSCREW

SETSCREW

SETSCREW

SLIDE VOLUME

CONNECTOR

T H E T R A N S F O R M E R C O R D

SHOULD NOT PASS OVER THE

CAPACITOR WHEN BOARD "A" IS

INSTALLED.

CAPACITOR

21

«
...
21
22
23
24
25
...
»

Содержание DC 3018


































Отзывы:

Нет отзывов