Janome DC 3018 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 33

Janome DC 3018 Скачать руководство пользователя страница 22

REFER TO THE DIAGRAM FOR LOCATING THE CONNECTOR POSTS TO WHICH EACH CONNECTORS

SHOULD BE CONNECTED.

CONNECTOR DIAGRAM

SLIDE VOLUME

PRINTED CIRCUIT

BOARD "F"

ZIGZAG WIDTH MOTOR

FEED MOTOR

LAMP

BUTTONHOLE

SENSOR

UPPER SHAFT

SENSOR

MACHINE SOCKET

(SECONDARY)

DC MOTOR

POWER TRANSFORMER

(PRIMARY CIRCUIT)

POWER TRANSFORMER

(SECONDARY)

MACHINE PLUG

(PRIMARY CIRCUIT)

BOBIN WINDER SWITCH

NOTE

TO DISCONNECT THE CONNECTORS:

1. GRASP THE CONNECTOR DIRECTLY WITH YOUR FINGERS AND PULL.

DO NOT PULL THE LEAD WIRE, AS THIS MAY DAMAGE THE CONTACT SLEEVE INSIDE THE CONNECTOR.

2. WHEN DISCONNECTING THE MACHINE SOCKET AND POWER TRANSFORMER CONNECTORS, PULL

THEM WHILE PUSHING THEM TOWARD THE PRINTED CIRCUIT BOARD TO UNLOCK THEM.

NOTE

TO CONNECT THE CONNECTORS:

1. BE SURE THAT THE COLOR OF EACH CONNECTOR CORRESPONDS TO THE COLOR OF THE

CONNECTOR POST ON THE PRINTED CIRCUIT BOARD (PCB) TO WHICH IT IS CONNECTED.

2. POSITION THE CONNECTOR CORRECTLY, THEN PUSH IT STRAIGHT DOWN UNTIL IT LOCKS IN PLACE.

20

«
...
20
21
22
23
24
...
»

Содержание DC 3018


































Отзывы:

Нет отзывов