Janome DC 3018 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 33

Janome DC 3018 Скачать руководство пользователя страница 21

MECHANICAL ADJUSTMENT

THREADER KNOB

HOOK

NEEDLE HOLE

REPLACING THE NEEDLE THREADER

COVER (WITH THE THREADER PLATE

ATTACHED

THREADER PLATE

SUPPORTER (A)

FIG. 1

VERTICAL ADJUSTMENT

THREADER

POSITION

SET PLATE

FIG. 3

FIG. 2

X

PIN (B)

SETSCREW

(D)

j

1. PUSH DOWN THE NEEDLE THREADER KNOB AND PULL THE NEEDLE THREADER PLATE (A) DOWN TO

REMOVE IT (SEE FIG 1).

2. TO INSTALL THE NEEDLE THREADER PLATE, LINE THE GROOVE UP WITH THE PIN (B) AND PUSH IT

UP TO SNAP FIT.

TO ADJUST THE THREADER PLATE POSITION:

1. IF THE HOOK ON THE THREADER PLATE TOUCHES THE LEFT OR RIGHT SIDE OF THE NEEDLE

GUIDE, LOOSEN SETSCREW (C) AND ADJUST THE HOOK POSITION (FIG 2).

2. IF THE HOOK ON THE THREADER PLATE TOUCHES THE TOP OR BOTTOM SIDE OF THE NEEDLE

GUIDE, LOOSEN SETSCREW (D) AND ADJUST THE HOOK POSITION (FIG.3)

REPLACEMENT AND ADJUSTMENT OF THE NEEDLE THREADER PLATE

IF THE HOOK OF THE THREADER PLATE IS DAMAGED, CHANGE OR ADJUST THE PART AS FOLLOWS:

TO CHANGE THE THREADER PLATE:

TO REMOVE:

ADJUSTMENT OF LEFT

OR RIGHT DIRECTION

THREADER PLATE

NUT

SETSCREW (C)

VIEW FROM "X"

19

«
...
19
20
21
22
23
...
»

Содержание DC 3018


































Отзывы:

Нет отзывов