Janome DC 3018 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 33

Janome DC 3018 Скачать руководство пользователя страница 12

MECHANICAL ADJUSTMENT

ECCENTRIC PIN

SETSCREW 3 X 4

NEEDLE PLATE HOLE

0.2 MM OR

MORE

0.2 MM OR

MORE

A=B

NEEDLE DROP POSITION

SET THE STITCH PATTERN AT " "; THE STANDARD NEEDLE DROP POSITION SHOULD BE AT THE

CENTER OF THE NEEDLE PLATE HOLE.

WHEN THE NEEDLE SWINGS IN MAXIMUM ZIGZAG WIDTH " ", THE DISTANCE BETWEEN BOTH

ENDS OF THE NEEDLE HOLE ON THE NEEDLE PLATE AND THE NEEDLE SHOULD BE 0.2 MM OR

MORE. IF NOT, ADJUST AS FOLLOWS.

1. TURN ON THE POWER SWITCH, SET THE STITCH PATTERN AT STRAIGHT " " AND THE ZIGZAG

WIDTH AT MAXIMUM " " THEN CHECK THE NEEDLE DROP POSITION.

2. IF THE NEEDLE DROP POSITION IS NOT IN THE CENTER OF THE NEEDLE PLATE HOLE WHEN THE

STRAIGHT STITCH IS SELECTED, OR IF THE CLEARANCE BETWEEN THE NEEDLE AND EDGE OF THE

NEEDLE PLATE HOLE ON BOTH SIDE IS LESS THAN 0.2 MM WHEN THE STITCH PATTERN IS SET TO

MAXIMUM ZIGZAG WIDTH, REMOVE THE FACE COVER AND LOOSEN THE SETSCREW, THEN ADJUST

THE NEEDLE DROP POSITION BY TURNING THE ECCENTRIC PIN.

NOTE

MAKE SURE THE ECCENTRIC PIN IS POSITIONED WITH ITS OFF-CENTER HEAD FACING DOWNWARD.

3. WHEN YOU HAVE FINISHED ADJUSTING THE NEEDLE DROP POSITION, TIGHTEN THE SETSCREW

AND INSTALL THE FACE COVER.

ADJUSTMENT PROCEDURE

ECCENTRIC PIN POSITION

(OFF -CENTER HEAD)

ADJUST THE NEEDLE DROP POSITION BY

TURNING THE ECCENTRIC PIN AS

10

«
...
10
11
12
13
14
...
»

Содержание DC 3018


































Отзывы:

Нет отзывов