Janome 502X Скачать руководство пользователя

Страница: 27 / 30

REPLACEMENT AND ADJUSTMENT OF NEEDLE THREADER PLATE

IF THE NEEDLE THREADER IS DAMAGED, REPLACE IT OR ADJUST AS FOLLOWS TO REPLACE THE

NEEDLE THREADER COVER:

1. PULL OUT THE THREADER COVER (DRAWING. 1).

2. TO ATTACH THE THREADER COVER, MATCH THE GROOVE TO THE PIN (B) AND INSERT THE

THREADER COVER (C).

ADJUSTMENT OF THREADER PLATE:

3. IF THE FOOK (D) IS TOUCHING THE RIGHT OR LEFT SIDE OF NEEDLE EYE, LOOSEN THE

SETSCREW (E) AND SLIDE THE THREADER PLATE (H). (SEE DRAWING2)

4. IF THE HOOK (D) IS TOUCHING THE TOP OR BOTTOM SIDE OF NEEDLE EYE, REMMOVE THE

FACE COVER AND LOOSEN THE SETSCREW (F) AND ADJUST THE THREADER POSITION SET

PLATE (G).

MECHANICAL ADJUSTMENT

THREADER KNOB

HOOK (D)

THREADER POSITION SET PLATE (G)

SETSCREW (F)

THREADER PLATE (H)

VIEW X

HOOK (D)

S E T S C R E W

(E)

DRAWING 1

PIN (B)

DRAWING 2

THREADER COVER (C)

www.promelectroavtomat.ru

Содержание 502X































Результаты поиска

Содержание 502X

Отзывы:

Похожие инструкции для 502X

Бренды по названию

Популярные бренды

Janome 502X, Руководство по обслуживанию

Результаты поиска

Содержание 502X

Отзывы:

Похожие инструкции для 502X

Бренды по названию

Популярные бренды