manualshive.com logo in svg

Janome 502X, Руководство по обслуживанию

Поделиться
Скачать
Janome 502X Скачать руководство пользователя страница 13

11

2-3 mm

TO CHECK:

   SET THE PATTERN SELECTOR DIAL AT “    “ AND MAXIMUM ZIGZAG WIDTH.

   IF THE NEEDLE MOVES SIDEWISE WHILE THE NEEDLE IS COMING OUT FROM THE FABRIC, ADJUST

   IT AS FOLLOWS:

   (THE NEEDLE SHOULD START SWINGING WHEN ITS TIP IS AT 2 MM (0.08”) TO 3 MM (0.12”) ABOVE

   THE NEEDLE PLATE IN UPWARD MOTION).

ADJUSTMENT PROCEDURE:

1. REMOVE THE FACE COVER AND FRONT COVER (SEE PAGES 6 AND 7).

2. SELECT THE PATTERN SELECTOR DIAL AT “     “ AND SET THE ZIGZAG WIDTH AT “5”.

3. LOOSEN THE TWO HEXAGONAL SOCKET SCREWS ON THE UPPER SHAFT WORM.

4. WHILE HOLDING THE UPPER SHAFT WORM IN PLACE, CAREFULLY TURN THE HANDWHEEL AND

    ADJUST SO THAT LATERAL NEEDLE SWING STARTS FROM A POSITION 2 MM (0.08”) TO 3 MM

    (0.12”) ABOVE THE NEEDLE PLATE IN RIGHT OUTFLOW MOTION.

5. TIGHTEN THE TWO HEXAGONAL SOCKET SCREWS ON THE UPPER SHAFT WORM.

6. ATTACH THE FRONT COVER AND FACE COVER.

NOTE:

MAKE SURE THAT THERE IS NO BACKLASH BETWEEN THE UPPER SHAFT WORM AND

                    CAM BLOCK GEAR, AND THE UPPER SHAFT SHOULD TURN SMOOTHLY.

NEEDLE PLATE

GEAR

UPPER SHAFT WORM

THE BACKLASH IS

INCREASED.

THE BACKLASH IS

DECREASED.

IF THE UPPER SHAFT WORM DEVIATES LATERALLY

WHEN TURNING THE UPPER SHAFT, THE BACKLASH

BETWEEN THE GEARS WILL CHANGE.

MECHANICAL ADJUSTMENT

NEEDLE SWING

HEXAGONAL SOCKET

SCREWS

(RIGHT OUTFLOW MOTION)

www.promelectroavtomat.ru

Содержание 502X































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды