Janome 502X Скачать руководство пользователя

Страница: 2 / 30

LOCATE AND IDENTIFY THE PARTS ....................................................................................1

WHAT TO DO WHEN .......................................................................................................2 - 4

THREADING OF MACHINE...................................................................................................5

SERVICE ACCESS

FACE COVER ........................................................................................................................6

FREE ARM LEGS COVER.....................................................................................................6

FRONT COVER......................................................................................................................7

REAR PANEL .........................................................................................................................8

MECHANICAL ADJUSTMENT

TOP TENSION .......................................................................................................................9

PRESSER BAR HEIGHT AND ALLIGNMENT .....................................................................10

NEEDLE SWING ..................................................................................................................11

STRAIGHT STITCHING (1) .................................................................................................12

NEEDLE DROP (2) ..............................................................................................................13

STRETCH STITCH BALANCE ............................................................................................14

FEED DOG HEIGHT ............................................................................................................15

NEEDLE BAR HEIGHT ........................................................................................................16

NEEDLE TO SHUTTLE TIMING ..........................................................................................17

NEEDLE CLEARANCE TO SHUTTLE ................................................................................18

BACKLASH (BETWEEN LOWER SHAFT GEAR AND SHUTTLE HOOK GEAR) ..............19

NEEDLE POISITION MISALIGNMENT ...............................................................................20

ZERO FEEDING .................................................................................................................21

BUTTONHOLE STITCH BALANCE .....................................................................................22

ZERO FEEDING OF BUTTONHOLE BARTACK .................................................................23

BUTTONHOLE FUNCTION .................................................................................................24

REPLACEMENT AND ADJUSTMENT OF NEEDLE THREADER PLATE ..........................25

MOTOR BELT TENSION .....................................................................................................26

WIRING OF TERMINAL BLOCK .........................................................................................27

OILING .................................................................................................................................28

TABLE OF CONTENTS

www.promelectroavtomat.ru

Содержание 502X































Результаты поиска

Содержание 502X

Отзывы:

Похожие инструкции для 502X

Бренды по названию

Популярные бренды

Janome 502X, Руководство по обслуживанию

Результаты поиска

Содержание 502X

Отзывы:

Похожие инструкции для 502X

Бренды по названию

Популярные бренды