background image

UMG 804

www.janitza.com

14

Voltage measurement

The voltage measurement inputs are suitable for measurements in the following power supply systems
Three-phase 4-conductor systems with nominal 
voltages up to

480 V AC 

Three-phase 3-conductor systems, unearthed,  
with nominal voltages up to 

277 V AC

From a safety and reliability perspective, the voltage measurement inputs are designed as follows

Overvoltage category

230 V: Cat II

24 V: CAT III

Protection of voltage measurement

Impedance limited plus clamping diodes / MOV

Measurement range L-N 

0 .. 277 V AC

Measurement range L-L 

0 .. 480 V AC

Resolution

0.01 V AC

Crest factor

1.9 @ 240 V AC

Impedance

2.5 MΩ

Power consumption

<0.1 A @ 277 V AC (< 3 W)

Sampling rate

40 kHz 

Frequency range of the fundamental oscillation
- Resolution

40 .. 70 Hz.

Digital inputs

Quantity

2

Digital outputs

Quantity

2

Switching voltage

30 V DC

Switching current

100 mA 

Cable lenght

screw in terminal block

Note:

 two inputs for dry contacts

Terminal connection capacity (digital inputs and outputs)

Rigid/flexible

22-16 AWG / 0.324-1.31 mm²

Flexible with core end sheath without plastic sleeve

22-16 AWG / 0.324-1.31 mm²

Flexible with core end sheath with plastic sleeve

22-16 AWG / 0.324-1.31 mm²

Tightening torque

5.0 Lb-In / 0.56 Nm

Stripping length

5 mm (0.20 in) recommeded

Current measurement on modules

Rated current

0 .. 600 A (external current transducer dependant)

Resolution

0.01 A

Crest factor

3.75 @ 100 % of 0.333 V signal

Overload for 1 s

200 %

Содержание 14.02.001























































































Отзывы: