janitza 14.02.001 Скачать руководство пользователя страница 52

Страница: 52 / 86

UMG 804

www.janitza.com

IP Address:

Default is always

192.168.5.77

NetMask

Gateway IP

Primary DNS IP

NTP server

: NTP server is utilized for date and time references. Consult your system adminis-

trator for details or leave as default and time will be synced to

time.google.com

BACnet UDP Port

: Only required for BACnet applications.

BACnet Device ID:

Only required for BACnet applications.

14.2 Network
14.2.1 Ethernet Settings

Ethernet
Serial

For any of the changes to be
captured, the user must click
on „Update Settings“, and then
confirm with „Apply Changes“.

·The Ethernet Settings tabs allows for all IP based

settings to be configured. These settings may
also be configured using the config.csv file via
USB drive or direct input from a Modbus write
command.

·The factory default IP is always

192.168.5.77

·The PC or device must be set to the same subnet

as the IP address on the UMG 804 (see modify-
ing subnet (i.e 1

92.168.5.XXX

) on PC for more

details).

·Lost IP address: The IP address can also be

revealed by inserting an USB into the UMG 804
and removing after approximately 20 seconds
and a IPSetting.txt file will be written on the USB
drive with the IP address.

·Note that if not using BACnet select disable

BACnet.

Содержание 14.02.001























































































Результаты поиска

Содержание 14.02.001

Отзывы:

Похожие инструкции для 14.02.001

Бренды по названию

Популярные бренды

janitza 14.02.001, Руководство пользователя и технические данные

Результаты поиска

Содержание 14.02.001

Отзывы:

Похожие инструкции для 14.02.001

Бренды по названию

Популярные бренды