Jandy WFTR Скачать руководство пользователя страница 4

Page 4 

ENGLISH

  

 

Jandy

®

 Pro Series Water Feature Pump   

|

   Installation and Operation Manual

Section 1. Important Safety Instructions 

READ AND FOLLOW ALL INSTRUCTIONS

1.1  Safety Instructions

All electrical work must be performed by a licensed electrician and conform to all national, state, and local codes. 

When installing and using this electrical equipment, basic safety precautions should always be followed, including the 

following:

 

WARNING

RISK OF SUCTION ENTRAPMENT HAZARD, WHICH, IF NOT AVOIDED, CAN RESULT IN SERIOUS INJURY 

OR DEATH. 

Do not block pump suction as this can cause severe injury or death. Do not use this pump for 

wading pools, shallow pools or spas containing bottom drains, unless the pump is connected to at least two 

functioning suction outlets.  Suction outlet (drain) covers must be certified to the latest published version of ANSI/

ASME A112.19.8. 

 

WARNING

To reduce the risk of injury, do not permit children to use this product.

 

WARNING

To reduce the risk of property damage or injury, do not attempt to change the backwash (multiport, slide, or full 

flow) valve position with the pump running.

 

WARNING

Jandy Pro Series pumps are powered by a high voltage electric motor and must be installed by a licensed or 

certified electrician or a qualified swimming pool service technician.

 

WARNING

Due to the potential risk of fire, electric shock, or injuries to persons, Jandy

 

Pumps must be installed in 

accordance with the National Electrical Code (NEC), all local electrical and safety codes, and the Occupational 

Safety and Health Act (OSHA). Copies of the NEC may be ordered from the National Fire Protection Association, 

470 Atlantic Ave., Boston, MA 02210, or received by contacting your local government inspection agency.

 

WARNING

Incorrectly installed equipment may fail, causing severe injury or property damage.

 

WARNING

•  Do not connect the system to an unregulated city water system or other external source of pressurized water 

producing pressures greater than 35 PSI.

•  Trapped air in system can cause the filter lid to be blown off, which can result in death, serious personal injury, 

or property damage. Be sure all air is out of the system before operating.

Содержание WFTR

























Отзывы: