J&M SpeedTender 500ST Скачать руководство пользователя страница 8

Страница: 8 / 51

1.0 Operations

1.1 Preparing the Towing Vehicle

Before towing the Speed Tender, refer to towing vehicle’s owner’s manual for information concerning hitch

capacities, hitch adjustments, and tire inflation.

Towing vehicle must be equipped with proper electric braking components.

NOTE: The Speed Tender is equipped with LED lights. The towing vehicle may require a

flasher upgrade for lights to operate properly.

Do not exceed towing vehicles GVWR (Gross Vehicle Weight Rating) or GCWR (Gross Combination Weight
Rating), or the maximum hitch load.

1.2 Preparing Speed Tender

Hydraulics: Check routing of all hydraulic hoses. Hoses should not be kinked, twisted or rubbing against sharp

edges. Check all hoses and fittings for hydraulic leaks. Tighten and /or repair or replace as required.

Lubrication: Lubricate Speed Tender as outlined in Service section 2.1. Refer to engine manual for proper fluid

levels in engine.

Tires/Wheels: Check tire pressures and maintain at recommended operating pressure. It is important to check

wheel nut/bolts for proper torque as recommended. You can find proper tire pressure and wheel torque located in

service manual section.

.3 Connecting Speed Tender to the Towing Vehicle

WARNING: Do not stand between the Speed Tender and tow vehicle when hooking up.

The Speed Tender comes with a Gooseneck Frame. The Gooseneck Frame can feature either a

2-5/16” ball coupler or a 5th Wheel hook up.

Back tow vehicle up to Speed Tender.

Align the vehicle’s ball with the coupler on the Speed Tender.

Lift tongue latch lever.

Lower jack to set Speed Tender coupler down on ball.

Latch coupler. Check to make sure that coupler is securely latched.

Raise jack.

Attach 7-way plug to tow vehicle. Check the length of the Speed Tender 7-way to make sure that

it is long enough to turn, but not too long to touch the ground.

NOTE: Check to make sure that lights are in proper operating condition and repair or

replace if necessary.

Connect the brake breakaway cable to towing vehicle.

Attach safety chains to tow vehicle by crossing chains. Allow enough slack in

chains necessary for turning.
10.

Test the brakes and all the lights on the Speed Tender

WARNING

: Check safety chains for broken, stretched or damaged link or end fittings.

Replace chains if found to be damaged. Do not weld safety chains.

Содержание SpeedTender 500ST




















































Результаты поиска

Содержание SpeedTender 500ST

Отзывы:

Похожие инструкции для SpeedTender 500ST

Бренды по названию

Популярные бренды

J&M SpeedTender 500ST, Руководство оператора

Результаты поиска

Содержание SpeedTender 500ST

Отзывы:

Похожие инструкции для SpeedTender 500ST

Бренды по названию

Популярные бренды