J&M SpeedTender 500ST Скачать руководство пользователя страница 48

Страница: 48 / 51

Auto Scale Shutoff Directions

To Toggle Switch

Ground

To Scale Display/Interface

To Valve Body

Deluxe Wireless Remote

•Starts/Stops Motor

•Raise/Lower Conveyer

•Open/Close Tank Doors

•Hydraulic Conveyer

•Auger Swing

•Tip Spout

•Electronic Auto Scale Shutoff

1. Turn Scale Head, Wireless Remote, and Wireless Toggle Switch on.

-The main screen showing gross and tared weight will display.

2. Press and release Scroll on the Wireless Remote.

-The setting for door weight and door selections (front or rear) will display.

3. Press and hold Scroll until the weight value starts to flash.

4. Using the up and down arrows just below the display in the center of the remote,

adjust the desired dispense weight.

5. Press and release Scroll

-The door setting will flash.

6. Using the up and down arrows just below the display in the center of the remote,

select which door you want to dispense from.

7. When settings are acceptable, press and hold Scroll for 3 seconds.

-The main screen will display again.

8. Press conveyer start to dispense the set amount of seed from the desired door.

-The door will automatically shut when the set amount of seed is dispensed

and the conveyor will turn off shortly after.

9. To dispense the same amount of seed from the same door, again press conveyer

start, then repeat the dispense cycle. *If the remote is turned off, steps 1-8 will need to be repeated.

SCROLL

USE THESE BUTTONS

TO ADJUST “DISPENSE

AMOUNT” AND “DOOR

TO DISPENSE FROM”

SETTING

MAIN SCREEN

AUTO SCALE SHUTOFF SCREEN

Содержание SpeedTender 500ST




















































Результаты поиска

Содержание SpeedTender 500ST

Отзывы:

Похожие инструкции для SpeedTender 500ST

Бренды по названию

Популярные бренды

J&M SpeedTender 500ST, Руководство оператора

Результаты поиска

Содержание SpeedTender 500ST

Отзывы:

Похожие инструкции для SpeedTender 500ST

Бренды по названию

Популярные бренды