background image

 

 

Modify, copy, or transfer the User's Guide, other documentation or any copy. 
Reverse engineer, decompile, or disassemble any program module or security device. 
 
This license is effective until terminated.  You may terminate it by destroying or returning 
the program, manuals, and all copies thereof.  This license will terminate if you fail to 
comply with any term or condition of this agreement. 
 

Limited Warranty 

XELTEK warrants that its products will be free from defects in workmanship and 
materials, and shall conform to specifications current at the time of shipment, for a period 
of one year from the date of shipment.  During the one year period, any defective software 
or hardware products will be repaired or replaced, at Seller's option, on a return to factory 
basis.   
This warranty applies only to products properly installed and operated within specified 
environmental conditions. 
XELTEK's responsibility under this warranty does not apply to: 
(a) 

Any product which has been repaired, worked upon, or altered by any person not 
duly authorized in writing by XELTEK; or 

(b) 

Any product which has been subject to misuse, negligence or accident, or whose 
serial number has been altered, defaced, or removed; or 

(c) 

Any fault induced into the program by physical damage to the diskette or to the 
corruption of the program by electronic or electrical or magnetic interference. 

All efforts have been made to verify the proper operation of the software and the accuracy 
of the User's Guide.  XELTEK does not warrant that the operation of the program will be 
uninterrupted or totally error free. 
New features and enhancements to the existing programs may be added, and verified 
program faults or necessary amendments will be rectified through the issue of periodic 
software revisions.  Notice of these may be sent to registered buyers only.  Failure to 
return the completed Software registration card with correct mailing address will exclude 
the purchaser from automatically receiving notification of revisions to the program.  
Software updates and revisions may be subject to a fee. 
XELTEK does not accept liability for any damages, including loss of profit or savings, 
other incidental or consequential damages arising out of the use, misuse, or inability to 
use the program. 
This warranty to repair or replace products not conforming to specification is specifically 
in lieu of all other warranties expressed or implied including, without limitation (to the 
extent permitted by law), the warranties of merchantability and fitness for use.  No agent 
or representative of XELTEK has any authority to bind XELTEK to any affirmation, 
representation, or warranty concerning products made by XELTEK; and XELTEK will 
have no liability whatsoever for any damage, loss, cost, or expense (whether direct, 
special or consequential) suffered or incurred by buyer if products fail to conform with 
XELTEK's warranty herein. 
 

3.2   Error Messages 
 

Содержание Superpro Series




























Отзывы: