JAI LQ-401CL Скачать руководство пользователя страница 9

Страница: 9 / 74

LQ-401CL

4. Locations and functions

4.1. Locations and functions

Fig. 1 Location of external features

1 Lens mount

M52 mount (*1)Note)

2 Camera Link connector 1

base connector (1)

(*2)Note)

3 Camera Link connector 2

medium connector (2) (*2)Note)

4 12-pin Hirose connector

DC +12, External trigger and RS-232C

5 DIP switch

SW-1 ( refer to chapter 4.2 for the details)

6 Button

For one-push auto white balance (Gain based)

LED indicator

Power, trigger input and operation indications

8 Camera mounting holes

8 x M3, depth 5mm (*3) Note)

*1) Note:

Rear protrusion on M52 mount lens must be less than 13mm.

F mount is also available. Rear protrusion for F mount lens is the same as M52 mount.
*2) Note: When a Camera Link

cable is connected to the camera, please do not excessively tighten

screws by using a driver. The Camera Link receptacle on the camera might be damaged.
For security, the strength to tighten screws is less than 0.291 Newton meter (Nm).
Tightening by hand is sufficient in order to achieve this.

*3) Note:

The depth of mounting hole is 5 mm. If the longer screws than 5 mm are used, they may

damage the circuit board inside.

Содержание LQ-401CL











































































Результаты поиска

Содержание LQ-401CL

Отзывы:

Похожие инструкции для LQ-401CL

Бренды по названию

Популярные бренды

JAI LQ-401CL, Руководство пользователя

Результаты поиска

Содержание LQ-401CL

Отзывы:

Похожие инструкции для LQ-401CL

Бренды по названию

Популярные бренды