JAI LQ-401CL Скачать руководство пользователя | Manualshive

Страница: 24 / 74

background image

LQ-401CL

23

Fig.21 Color shading correction concept drawing

Note:



For this function, no reference value is stored in the camera.

Operating procedure for individual R, ,B and NIR channel shading correction:

1.    Before making adjustment, approximately 30 minutes of warm up is required.
2.    Make sure the output signal is not saturated (<80% of full output is recommended)
3.    Set command PGC=2 and SDC=2.
4.    Set command SDR to 1 to initiate shading correction.
5.    If desired, set command PGR to 0 to activate flat-field (pixel gain) correction to

correct for pixel response non-uniformity.

6. Again set SDR=1 after running the flat-field (pixel gain) correction

Please note that before adjusting the shading, the white balance must be adjusted

.

6.2.11 Lateral chromatic aberration

This function compensates for lateral chromatic aberration of lenses. Lateral chromatic aberration
causes different line lengths for the R, G, B and NIR rays at the focal point. This function enables
compensation data for up to three lenses to be stored.

The compensation data specifies how many

pixels the R, B and NIR channels should be stretched or shortened to match the line length of the G
channel which is the reference. The range of correction is minus three pixels to plus three pixels.
In order to realize this function, the LQ-400CL uses an FIR (finite impulse response) filter for R, B
and NIR channels. The filter’s response is determined by a set of 7 types of filter coefficients. The
4096 pixels that make up a line are divided in 16 blocks, with each block having 256 pixels.
To compensate lateral chromatic aberration, the 7 types of coefficients are set for each block.
In the factory, a default set of 112 data elements (7 types x 16 blocks) are calculated and stored.

4096th Pixel

Pixel number in each block: 256 pixels

Note: Restrictions for this function
In order to adjust properly lateral chromatic aberration, the difference between G and R or B  or
NIR  on  right  and  left  sides  should  be  equal.  Otherwise,  the  compensation  may  not  be  properly
executed.

The  following  screen  is  used  for  creating  up  to  three  user-defined  sets  of  lateral  chromatic
aberration data in the camera control tool.

«
...
22
23
24
25
26
...
»

Содержание LQ-401CL











































































Отзывы:

Нет отзывов

Похожие инструкции для LQ-401CL

Бренд: Samsung Страницы: 1

Бренд: Hama Страницы: 60

Бренд: SwissPhone Страницы: 2

VKC-1381/IR-3.6

Бренд: Eneo Страницы: 8

Бренд: Northern Страницы: 32

Бренд: AccuLine Страницы: 2

Бренд: Arecont Vision Страницы: 3

Бренд: Air Specialties Express Страницы: 4

Бренд: Abus Страницы: 4

Бренд: QOLSYS Страницы: 2

Бренд: SIM Страницы: 2

Бренд: Velleman Страницы: 21

Бренд: Idis Страницы: 8

Бренд: Velleman Страницы: 4

Бренд: Esse-ti Страницы: 44

Бренд: ACTi Страницы: 18

Бренд: Safety Vision Страницы: 12

Бренд: Motorline professional Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды