JAI GOX-2402M-PGE, Руководство пользователя

Страница: 69 / 88

Setting range Default value Description
Configure pulse generator settings.
1〜4096 4 Set the division value for the prescaler (12 bit) using PixelClock as the base
clock.
0.0181274〜74.25 0.45 Set the clock used for the pulse generator.
This value is calculated using the [ClockPreScaler] value as a base.
PulseGenerator0 PulseGenerator0 Select the pulse generator.
PulseGeneratorLength 1〜1048575 618750 Set the maximum count-up value as a clock count.
PulseGeneratorLengthMs (ms) 1 / PulseGeneratorClock
(MHz) 〜1048575 /
PulseGeneratorClock (MHz) 33.3333 Set the maximum count-up value in milliseconds.
This value is calculated using the [PulseGeneratorLength] value as a base.
The setting range varies depending on the [ClockPreScaler] value.
PulseGeneratorFrequency (Hz) PulseGeneratorClock (MHz)
÷ 1048575 x 1000000 〜
PulseGeneratorClock (MHz) x
1000000 30 Set the maximum count-up value as a frequency.
This value is calculated using the [PulseGeneratorLength] value as a base.
PulseGeneratorStartPoint 0 〜 1048574 0 Set the start point of the High interval as a clock count.
When the counter reaches this value, the output will be 1.
PulseGeneratorStartPointMs
(ms) 0 〜 1048575 /
PulseGeneratorClock (MHz) 0 Set the start point of the High interval in milliseconds.
When the counter reaches this value, the output will be 1.
The setting range varies depending on the [ClockPreScaler] value.
PulseGeneratorEndPoint 1 〜 1048575 464063 Set the start point of the Low interval as a clock count.
When the counter reaches this value, the output will be 0.
PulseGeneratorEndPointMs (ms) 1/ PulseGeneratorClock
(MHz) 〜
1048575 /
PulseGeneratorClock (MHz) 25 Set the start point of the Low interval in milliseconds.
When the counter reaches this value, the output will be 0.
The setting range varies depending on the [ClockPreScaler] value.
PulseGeneratorPulseWidth (ms) ー 25 Display the High interval width of the pulse in milliseconds.
The duration between the Start Point and End Point is calculated. The setting range varies
depending on the [ClockPreScaler] value.
PulseGeneratorRepeatCount 0 〜 255 0 Set the repeat count for the counter.
When this is set to [0], a free counter is enabled with no repeat limit.
PulseGeneratorClearActivation Off,
LevelHigh, LevelLow,
RisingEdge, FallingEdge Off Set the clear signal condition for the count clear input of the pulse generator.
PulseGeneratorClearSource ー Low Select the count clear input signal source.
[Setting range]
Low, High, AcquisitionTriggerWait, AcquisitionActive, FrameTriggerWait,
FrameActive, ExposureActive,
UserOutput0, UserOutput1, UserOutput2, UserOutput3,
Action1, Action2, Line5, Nand0Out, Nand1Out
PulseGeneratorClearSyncMode 0:Async Mode
1:Sync Mode 0:Async Mode Select the sync mode for the count clear input signal.
Configure LUT settings.
Red, Green, Blue Red Select the LUT channel to control. (color model only)
0〜256 0 Set the LUT index table number.
LUTValue 0〜4095 Gamma=1.0 Set the LUT value.
0〜10000 0 PendingAck function test command.
The camera waits for TestPendingAck (ms) time and returns an Ack response.
PulseGeneratorSelector
PulseGeneratorClock (MHz)
ClockPreScaler
TestPendingAck (ms)
i) TestControl
LUTIndex
LUTSelector
h) LUTControl
g) PulseGenerator
Item
— 6 9 —
Go-X Series GigE Vision I/F