JAI CB-140GE Скачать руководство пользователя страница 32

Страница: 32 / 76

CM-140GE / -RA/-UV / CB-140GE / -RA

- 30 -

8. Network configuration



For details of the network settings, please refer to the “Getting Started

Guide” supplied with the JAI SDK.

8.1. GigEVision Standard interface

The CM-140GE and CB-140GE series are designed in accordance with the GigE Vision

standard. Digital images are transmitted over Cat5e or Cat6 Ethernet cables. All camera

functions are also controlled via the GigE Vision interface.

The camera can operate in Continuous mode, providing an endless stream of images. For

capturing individual images related to a specific event, the camera can also be triggered.

For precise triggering, it is recommended to use a hardware trigger applied to the Hirose

12-pin connector. It is also possible to initiate a software trigger through the GigE Vision

interface. However, when using a software trigger, certain latency inherent to the GigE

interface must be expected. This latency, which manifests itself as jitter, greatly depends

on the general conditions and traffic on the GigE connection. The frame rate described in

this manual is for the ideal case and may deteriorate depending on conditions.

When using multiple cameras (going through a switch and/or a single path) or when

operating in a system with limited transmission bandwidth the Delayed Readout Mode and

Inter-Packet Delay functions can be useful.

8.2. Equipment to configure the network system

8.2.1 PC
The PC used should have the following performance or better

1) Recommended CPU

: Core2 Duo 2.4GHz or better,

Better than Core2 Extreme

2) Recommended memory

: 2Gbyte or more

3) Video card

: Better than PCI Express Bus Ver.1.0 x16

VRAM should be better than 256MByte, DDR2

4) Other

: The resident software should not be used

8.2.2 Cables

GigEVision configures the system by using 1000BASE-T. (100BASE-T can be used with

some restriction. Refer to chapter 8.3.6). In the market, CAT5e (125MHz), CAT6 (250MHz)

and CAT7 (600MHz) cables are available for 1000BASE-T. There are crossover cables and

straight through cables available. Currently, as most equipment

complies with Auto MDI/MDI-X, please use straight through cables. (Among crossover

cables, a half crossover type exists, which the Ethernet will recognize as 100BASE-T).

8.2.3 Network card (NIC)

The network card should comply with 1000BASE-T and also have the capability of

JUMBO FRAMES. When the jumbo frame size is set at a larger number, the load on the

CPU will be decreased. Additionally, as the overhead of the packet is decreased, the

transmission will have more redundancy.

Содержание CB-140GE













































































Результаты поиска

Содержание CB-140GE

Отзывы:

Похожие инструкции для CB-140GE

Бренды по названию

Популярные бренды

JAI CB-140GE, Руководство пользователя

Результаты поиска

Содержание CB-140GE

Отзывы:

Похожие инструкции для CB-140GE

Бренды по названию

Популярные бренды