JAI CB-140GE Скачать руководство пользователя страница 8

Страница: 8 / 76

CM-140GE / -RA/-UV / CB-140GE / -RA

- 6 -

To customers who use UV version

The sensor used in the CM-140MCL-UV, CM-140PMCL-UV and CM-140GE-UV utilizes a special

process in order to achieve sensitivity in the ultraviolet spectrum.

Because of this, this sensor will typically begin to exhibit reduced overall sensitivity more

rapidly than a conventional sensor.

Based on the results of lifecycle acceleration tests, it is projected that this sensor will start

to degrade in approximately one and a half years under 24-hour continuous operation or in

approximately 4 years if an 8-hour-per-day duty cycle is used.

Due to this characteristic, it may be necessary to replace the camera periodically.

Note: If the sensor is subjected to light with 1000 times the intensity of the CCD’s saturation

level, degradation will begin in approximately 48 hours. It is therefore advised that lighting of

this intensity (1000 times the sensor’s saturation level) never be used.

Содержание CB-140GE













































































Результаты поиска

Содержание CB-140GE

Отзывы:

Похожие инструкции для CB-140GE

Бренды по названию

Популярные бренды

JAI CB-140GE, Руководство пользователя

Результаты поиска

Содержание CB-140GE

Отзывы:

Похожие инструкции для CB-140GE

Бренды по названию

Популярные бренды