JAI AB-201CL страница 63 Скачать руководство пользователя

Страница: 63 / 68

AM-201CL / AB-201CL

- 61 -

12.2 Specifications table

Specifications

AM-201CL

AB-201CL

Scanning system

Progressive scan, 4 taps

Synchronizing system

Internal

Image sensor

2/3 inch Monochrome interline CCD 2/3 inch Bayer color interline CCD

Sensing area

10.56 (h) x 5.94 (v) mm 12.1 mm diagonal

Cell size

5.5 (h) x 5.5 (v)



Active pixels (for output)

1920 (h) x 1080 (v)

Pixel clock(sensor)

40 MHz

Horizontal (Camera Link)

35.398 KHz (1H=28.25µs) (2260clocks per line) (Pixel clock 80MHz)

Vertical

Total lines 1102 (Effective 1080)

Frame rate
(Full resolution)
2 tap output

Timed Trigger OFF
(Continuous)

64.2fps (15.56ms)

Bayer output

64.2fps (15.56ms)

Timed Trigger ON

64.2fps (15.56ms)

Bayer output

64.2fps (15.56ms)

Trigger Width

64.2fps (15.56ms)

Bayer output

64.2fps (15.56ms)

PIV

32.2fps (31.13ms)

Bayer output

32.2fps (31.13ms)

Pre-Dump

64.2fps +Fast dump + Exposure time

Bayer output
64.2fps +Fast dump + Exposure
time

Frame rate
(Full resolution)
1 tap output

Timed Trigger OFF
(Continuous)

32.2fps(31.13ms)

Bayer output /RGB color output

32.2fps (31.13ms)

Timed Trigger ON

32.2fps(31.13ms)

Bayer output /RGB color output

32.2fps (31.13ms)

Trigger Width

32.2fps(31.13ms)

Bayer output /RGB color output

32.2fps (31.13ms)

PIV

16.1ps(62.1ms)

Bayer output /RGB color output

16.1fps (62.1ms)

Pre-Dump

32.2fps +Fast dump + Exposure time

Bayer output /RGB color output
32.2fps +Fast dump + Exposure
time

Image Format

Full resolution

1920(h) x 1080(v)

Bayer 1920(h) x 1080(v)

RGB 1920(h) x 1080(v)

Binning (h x v)

1 x 2 1920(h) x 540(v)
2 x 1 960(h) x 1080(v)

2 x 2 960(h) x 540(v)

AOI

Height 1 line / step

Offset Y 1 line / step

Height 2 line / step

Offset Y 2 line / step

Note: number of horizontal pixels cannot be changed.

Sensitivity on sensor (minimum)

0.14 Lux (Max. gain, Shutter OFF,

50% video, w/IR cut filter )

3200K

0.21 Lux (Max. gain, Shutter

OFF,50% Green, )

4600K

S/N ratio

More than 57 dB (0dB gain, CCD output=300mV)

Digital
Video output
Camera Link

Pixel format

1 tap, 2 taps selectable

Pixel clock

80 MHz

Pixel bit depth

8-bit, 10-bit, 12-bit

BAYER 8-bit, 10-bit, 12-bit

RGB 8-bit per color

Iris video output

Analog, 0.7 V p-p with 0.3V H.sync

Sync output

Camera Link : FVAL, LVAL, DVAL, EEN

Hirose 12-pin: XEEN, 4V p-p (No termination)

Содержание AB-201CL





































































Результаты поиска

Содержание AB-201CL

Отзывы:

Похожие инструкции для AB-201CL

Бренды по названию

Популярные бренды

JAI AB-201CL, Руководство пользователя

Результаты поиска

Содержание AB-201CL

Отзывы:

Похожие инструкции для AB-201CL

Бренды по названию

Популярные бренды