JAI AB-201CL Скачать руководство пользователя страница 36

Страница: 36 / 68

AM-201CL / AB-201CL

- 34 -

7.7. Trigger width mode (so-called PWC)

In this mode, the exposure time is equal to the trigger pulse width. Accordingly, longer
exposure times are supported. Additional settings determine if the trigger pulse can be
accepted during the exposure period.

The frame rate of full pixels readout is 64.2fps for 2 tap output and 32.2fps for 1 tap
output.

Primary settings to use this mode

Sensor Digitization Taps: SDT= 0 (Two taps) SDT=1 (One tap)

Acquisition control

Acquisition frame rate:

AR= 1

～

42964

Exposure control

Exposure mode:

EM=2 (Trigger width)

Trigger control

Trigger mode: TM=1 (ON)
Trigger overlap: TO=0 (OFF) or 1=(Readout)
OFF: LVALsync

、

Readout:LVALsync/async automatic setting

Trigger source: TI=0 (Camera Link, default)

or 1(Hirose 12-pin)

Trigger Activation: TA=0 (Rising edge), 1=

（

Falling edge

）

, 2=(Any edge)

Minimum interval of the trigger pulse

2 tap output

FULL

2/3 AOI 1/2 AOI 1/4 AOI 1/8 AOI

Minimum frame line

552

416

349

248

197

1 tap output

FULL

2/3 AOI 1/2 AOI 1/4 AOI 1/8 AOI

Minimum frame line

1100

830

695

493

392

Note: The readout area for each AOI is the centered readout (same lines for upper and

lower)

7.7.1 If the overlap setting is “Non Overlap”

Binning Mode

Off, 2 x 1

5.24

s ± 0.5

2L (min.)

6.5L to 7.5L

37.2

s ± 0.05

1 x 2, 2 x 2

7.96

s ± 0.5

2L (min.)

6.5L to 7.5L

37.2

s ± 0.05

Fig.33 Overlap = OFF

Содержание AB-201CL





































































Результаты поиска

Содержание AB-201CL

Отзывы:

JAI AB-201CL, Руководство пользователя, Страница: 36 / 68

Результаты поиска

Содержание AB-201CL

Отзывы: